Kenwood Cassette Player KRC 266 User Manual

CASSETTE RECEIVER  
KRC-266  
KRC-266S  
INSTRUCTION MANUAL  
© B64-2433-00/00 (MN)  
 
Safety precautions  
IMPORTANT INFORMATION  
2WARNING  
2CAUTION  
About CD players/disc changers  
connected to this unit:  
KENWOOD disc changers/ CD players  
released in 1998 or later can be connected to  
this unit.  
Refer to the catalog for connectable models of  
disc changers/ CD players.  
Note that any KENWOOD disc changers/ CD  
players released in 1997 or earlier and disc  
changers made by other makers cannot be  
connected to this unit.  
Unsupported connection may result in break or  
failure.  
Setting the "O-N Switch" to the "N" position for  
the applicable KENWOOD disc changers/ CD  
players.  
The functions that can be used and the  
information that can be displayed will differ  
depending on the models being connected.  
To prevent injury or fire, take the  
following precautions:  
• Insert the unit all the way in until it is fully  
locked in place. Otherwise it may fall out of  
place when jolted.  
• When extending the ignition, battery, or  
ground wires, make sure to use automotive-  
grade wires or other wires with a 0.75mm  
(AWG18) or more to prevent wire  
deterioration and damage to the wire  
coating.  
To prevent a short circuit, never put or leave  
any metallic objects (such as coins or metal  
tools) inside the unit.  
• If the unit starts to emit smoke or strange  
smells, turn off the power immediately and  
consult your Kenwood dealer.  
• Make sure not to get your fingers caught  
between the faceplate and the unit.  
To prevent damage to the machine,  
take the following precautions:  
• Make sure to ground the unit to a negative  
12V DC power supply.  
• Do not open the top or bottom covers of the  
unit.  
• Do not install the unit in a spot exposed to  
direct sunlight or excessive heat or humidity.  
Also avoid places with too much dust or the  
possibility of water splashing.  
• Do not set the removed faceplate or the  
faceplate case in areas exposed to direct  
sunlight, excessive heat or humidity. Also  
avoid places with too much dust or the  
possibility of water splashing.  
To prevent deterioration, do not touch the  
terminals of the unit or faceplate with your  
fingers.  
2
You can damage both your unit and the CD  
changer if you connect them incorrectly.  
• Do not subject the faceplate to excessive  
shock, as it is a piece of precision  
equipment.  
• Be careful not to drop the unit or subject it to  
strong shock.  
The unit may break or crack because it  
contains glass parts.  
• Do not touch the liquid crystal fluid if the  
LCD is damaged or broken due to shock. The  
liquid crystal fluid may be dangerous to your  
health or even fatal.  
If the liquid crystal fluid from the LCD  
contacts your body or clothing, wash it off  
with soap immediately.  
• When replacing a fuse, only use a new one  
with the prescribed rating. Using a fuse with  
the wrong rating may cause your unit to  
malfunction.  
To prevent a short circuit when replacing a  
fuse, first disconnect the wiring harness.  
• Do not place any object between the  
faceplate and the unit.  
• Do not use your own screws. Use only the  
screws provided. If you use the wrong  
screws, you could damage the unit.  
— 3 —  
 
Safety precautions  
Cleaning the Faceplate Terminals  
If the terminals on the unit or faceplate get  
dirty, wipe them with a dry, soft cloth.  
NOTE  
• If you experience problems during  
installation, consult your Kenwood dealer.  
• If the unit does not seem to be working  
right, try pressing the reset button first. If  
that does not solve the problem, consult  
your Kenwood dealer.  
• Press the reset button if the Disc auto  
changer fails to operate correctly. Normal  
operation should be resloved.  
Cleaning the Unit  
If the faceplate of this unit is stained, wipe it  
with a dry soft cloth such as a silicon cloth.  
If the faceplate is stained badly, wipe the stain  
off with a cloth moistened with neutral  
cleaner, then wipe neutral detergent off.  
Applying spray cleaner directly to the unit may  
affect its mechanical parts. Wiping the  
faceplate with a hard cloth or using a volatile  
liquid such as thinner or alcohol may scratch  
the surface or erases characters.  
Reset button  
About Cassette tape  
• Characters in the LCD may become difficult  
to read in temperatures below 41 ˚F (5 ˚C).  
Cleaning the tape head  
• The illustrations of the display and the panel  
appearing in this manual are examples used  
to explain more clearly how the controls are  
used. Therefore, what appears on the display  
in the illustrations may differ from what  
appears on the display on the actual  
equipment, and some of the illustrations on  
the display may represent something  
impossible in actual operation.  
When there’s noise or the sound quality is bad  
during tape play the tape head maybe dirty,  
clean the tape head.  
About Cassette tape  
• If the tape is slack tighten it.  
• If the cassette tape label is peeling off glue it  
on again.  
• Don’t use deformed cassette tape.  
• Don’t place cassette tape on the dashboard  
etc. where the temperature is high.  
• Don’t use cassette tape that’s 100 minutes  
long or longer.  
— 4 —  
 
General features  
Power  
Release button  
Turning ON the Power  
CLK/  
ADJ  
SRC/  
Press the [SRC] button.  
u
FM ¢  
4
PWR OFF  
Turning OFF the Power  
Press the [PWR OFF] button for at least 1 second.  
Selecting the Source  
Press the [SRC] button.  
Source required  
Display  
d
Tuner  
Tape  
"TUnE"  
"TAPE"  
"DISC"  
"OFF"  
AUD/  
A.ADJ  
ATT/  
LOUD  
#1 - 5  
AM  
External disc  
Standby (Illumination only mode)  
Clock display  
ATT indicator  
Clock indicator  
LOUD indicator  
— 5 —  
 
General features  
2 Enter Control mode  
Volume  
Press the [AUD] button.  
Increasing Volume  
3 Select the Sound type  
Press the [#1] [#5] button.  
Press button  
Press the [u] button.  
Decreasing Volume  
Sound setting  
Display  
Press the [d] button.  
[#1]  
[#2]  
[#3]  
[#4]  
[#5]  
Flat  
Rock  
Pops/ Top40  
Jazz  
Easy  
"DB-1"  
"DB-2"  
"DB-3"  
"DB-4"  
"DB-5"  
Attenuator  
Turning the volume down quickly.  
When the dB(Sound Coordinate) setting is changed, the Bass and  
Treble set in audio control replace the dB(Sound Coordinate) values.  
Press the [ATT] button.  
Each time the button is pressed the Attenuator turns ON or OFF.  
When it’s ON, the "ATT" indicator blinks.  
4 Exit Control mode  
Press the [AUD] button.  
Loudness  
Compensating for low and high tones during low volume.  
Audio Control  
Press the [LOUD] button for at least 1 second.  
Each time the button is pressed for at least 1 second the  
Loudness turns ON or OFF.  
1 Select the source for adjustment  
Press the [SRC] button.  
When it’s ON, "LOUD" indicator is ON.  
2 Enter Audio Control mode  
Press the [A.ADJ] button for at least 1 second.  
3 Select the Audio item for adjustment  
Press the [FM] or [AM] button.  
dB (Sound Coordinate)  
Each time the button is pressed the items that can be adjusted  
switch as shown below.  
You can recall the best sound setting preset for different types of  
the music.  
4 Adjust the Audio item  
Press the [4] or [¢] button.  
1 Select the source to set  
Press the [SRC] button.  
— 6 —  
 
Adjustment Item  
Display  
Range  
Theft Deterrent Faceplate  
The faceplate of the unit can be detached and taken with you,  
helping to deter theft.  
Bass level  
Treble level  
Balance  
"BAS"  
"TRE"  
"BL"  
–4 — 4  
–4 — 4  
L15 — R15  
R15 — F15  
Removing the Faceplate  
Fader  
"FD"  
Press the Release button.  
The faceplate is unlocked, allowing you to detach it.  
5 Exit Audio Control mode  
Press the [A.ADJ] button.  
• The faceplate is a precision piece of equipment and can be  
damaged by shocks or jolts. For that reason, keep the faceplate in  
its special storage case while detached.  
• Do not expose the faceplate or its storage case to direct sunlight  
or excessive heat or humidity. Also avoid places with too much  
dust or the possibility of water splashing.  
Switching Clock Display  
Switching the displayed information.  
Press the [CLK] button.  
Reattaching the Faceplate  
1 Align the projections on the unit with the grooves on the  
faceplate.  
Each time the button is pressed it switches between clock  
display and current source.  
During clock display the clock indicator is ON.  
Adjusting Clock  
1 Select the clock display  
2 Push the faceplate in until it clicks.  
The faceplate is locked in place, allowing you to use the unit.  
Press the [CLK] button.  
2 Enter clock adjustment mode  
Press the [CLK] button for at least 2 seconds.  
The clock display blinks.  
3 Adjust the hours  
Press the [FM] or [AM] button.  
Adjust the minutes  
Press the [4] or [¢] button.  
4 Exit clock adjustment mode  
Press the [CLK] button.  
— 7 —  
 
Tuner features  
Tuning Mode  
AUTO/  
AME  
Choose the tuning mode.  
FM/  
CRSC  
Press the [AUTO] button.  
Each time the button is pressed the Tuning mode switches as  
shown below.  
SRC  
¢
4
Tuning mode  
Display  
Operation  
Auto seek  
"AUTO"  
indicator  
Automatic search for a station.  
Manual  
Normal manual tuning control.  
#1 - 6  
AM  
Tuning  
Selecting the station.  
1 Select tuner source  
Press the [SRC] button.  
Select the "TUnE" display.  
Frequency display Preset station number  
2 Select the band  
STEREO indicator  
AUTO indicator  
Press the [FM] or [AM] button.  
Each time the [FM] button is pressed it switches between the  
FM1, FM2, and FM3 bands.  
3 Tune up or down the band  
Press the [4] or [¢] button.  
Band display  
(CRSC)indicator  
During reception of stereo stations the "STEREO" indicator is ON.  
— 8 —  
 
2 Call up the station  
Press the [#1] [#6] button.  
Station Preset Memory  
Putting the station in the memory.  
1 Select the band  
Press the [FM] or [AM] button.  
CRSC (Clean Reception System Circuit)  
Temporarily have reception switched from stereo to mono to  
reduce multi-path noise when listening to the FM station.  
2 Select the frequency to put in the memory  
Press the [4] or [¢] button.  
3 Put the frequency in the memory  
Press the [CRSC] button for at least 1 second.  
Each time the button is pressed CRSC turns ON or OFF.  
Press the [#1] — [#6] button for at least 2 seconds.  
The preset number display blinks 1 time.  
On each band, 1 station can be put in the memory on each [#1]  
— [#6] button.  
When it's ON, the "  
"(CRSC) indicator is ON.  
Frequency Step Setting  
Changing the tuning frequency step.  
The original setting is FM band 50 kHz, and AM band 9 kHz.  
Auto Memory Entry  
Putting stations with good reception in the memory  
automatically.  
1 Turn the power OFF  
Press the [SRC] button for at least 1 second.  
1 Select the band for Auto Memory Entry  
Press the [FM] or [AM] button.  
2 Switch the frequency step  
2 Open Auto Memory Entry  
Press the [AME] button for at least 2 seconds.  
When 6 stations that can be received are put in the memory  
Auto Memory Entry closes.  
While pressing the [#1] and [#5] button, press the [SRC]  
button.  
The frequency step changes to FM band 200 kHz, and AM band  
10 kHz.  
• When the same operation is repeated, it returns to the original  
setting.  
• When the frequency step is switched, the frequencies in the  
memory are deleted.  
Preset Tuning  
Calling up the stations in the memory.  
1 Select the band  
Press the [FM] or [AM] button.  
— 9 —  
 
Cassette player features  
Playing Cassette Tapes  
When the Cassette Tape is inserted  
Press the [SRC] button.  
FF  
REW  
SRC  
0
Select the "TAPE" display.  
When you want to listen to the reverse side  
Press the [REW] and [FF] button at the same time.  
Eject the Cassette Tape  
Press the [0] button.  
Fast Forwarding and Rewinding  
TC  
Fast Forwarding  
Press the [FF] button.  
If it's stopped press [REW] button.  
Rewinding  
Press the [REW] button.  
If it's stopped press the [FF] button.  
T.CALL indicator  
Tape indicator  
Tuner Call  
Switching to the radio automatically during Fast Forwarding and  
Rewinding.  
Press the [TC] button.  
Each time the button is pressed the Tuner Call turns ON or OFF.  
When it's ON, the "T.CALL" indicator is ON.  
When you turn ON the Tuner Call function, the motorized antenna  
will extend automatically.  
— 10 —  
 
External disc control features  
Playing External Disc  
Playing discs set in the optional accessory disc player connected  
to this unit.  
SRC  
¢
4
DISC+  
Press the [SRC] button.  
Select the display for the disc player you want.  
Display examples:  
Display  
Disc player  
"DISC"  
CD player  
CD changer/ MD changer  
• Disc #10 is displayed as "0".  
• The functions that can be used and the information that can be  
displayed will differ depending on the external disc players being  
connected.  
SCAN  
REP  
M.RDM  
D.SCN  
DISC-  
RDM  
Fast Forwarding and Reversing  
Fast Forwarding  
REP indicator  
RDM indicator  
Hold down on the [¢] button.  
Release your finger to play the disc at that point.  
Disc number  
Track number  
Reversing  
Hold down on the [4] button.  
Release your finger to play the disc at that point.  
SCN indicator  
— 11 —  
 
External disc control features  
1 Start Track Scan  
Track Search  
Selecting the song you want to hear.  
Press the [4] or [¢] button.  
Press the [SCAN] button.  
"SCN" indicator is ON.  
2 Release it when the song you want to listen to is played  
Press the [SCAN] button.  
Album Search (Function of disc changer)  
Selecting the disc you want to hear.  
Disc Scan (Function of disc changer)  
Successively play the beginning of each disc on a changer  
until you find the one that you want to listen to.  
Press the [DISC–] or [DISC+] button.  
1 Start Disc Scan  
Press the [D.SCN] button.  
The disc number blinks.  
Track/Album Repeat  
Replaying the song/disc you're listening to.  
2 Release it when the disc you want to listen to is played  
Press the [D.SCN] button.  
Press the [REP] button.  
Each time the button is pressed the Repeat Play switches as  
shown below.  
Repeat play  
Display  
Track Repeat  
"REP" indicator is ON & Track No.  
blinks.  
Random Play  
Playing all the songs on the disc in random order.  
Album Repeat  
Repeat OFF  
"REP" indicator is ON & Disc No. blinks.  
(Function of disc changer)  
---  
Press the [RDM] button.  
Each time the button is pressed Random Play turns ON or OFF.  
When it's ON, the "RDM" indicator is ON and the track number  
blinks.  
When the [¢] button is pressed, the next song select starts.  
Track Scan  
Playing the first part of each song on the disc you are listening  
to and searching for the song you want to listen to.  
— 12 —  
 
Magazine Random Play  
(Function of disc changer)  
Play the songs on all the discs in the disc changer in random  
order.  
Press the [M.RDM] button.  
Each time the button is pressed the Magazine Random Play turns  
ON or OFF.  
When it's ON, the "RDM" indicator is ON and the track and disc  
number blink.  
When the [¢] button is pressed, the next song select starts.  
— 13 —  
 
Accessories  
External view  
External view  
......... Number of items  
2WARNING  
......... Number of items  
If you connect the ignition wire (red) and the battery wire (yellow)  
to the car chassis (ground), you may cause a short circuit, that in  
turn may start a fire. Always connect those wires to the power  
source running through the fuse box.  
1
2
3
4
5
.........4  
.........4  
.........1  
.........1  
.........2  
2CAUTION  
• If your car's ignition does not have an ACC position, connect the  
ignition wires to a power source that can be turned on and off  
with the ignition key. If you connect the ignition wire to a power  
source with a constant voltage supply, as with battery wires, the  
battery may die.  
• If the console has a lid, make sure to install the unit so that the  
faceplate will not hit the lid when closing and opening.  
• If the fuse blows, first make sure the wires aren’t touching to  
cause a short circuit, then replace the old fuse with one with the  
same rating.  
The use of any accessories except for those provided might result in  
damage to the unit. Make sure only to use the accessories shipped with  
the unit, as shown above.  
• Insulate unconnected wires with vinyl tape or other similar  
material. To prevent a short circuit, do not remove the caps on  
the ends of the unconnected wires or the terminals.  
• Connect the speaker wires correctly to the terminals to which  
they correspond. The unit may be damaged or fail to work if you  
share the - wires or ground them to any metal part in the car.  
• When only two speakers are being connected to the system,  
connect the connectors either to both the front output terminals  
or to both the rear output terminals (do not mix front and rear).  
For example, if you connect the + connector of the left speaker  
to a front output terminal, do not connect the - connector to a  
rear output terminal  
Installation Procedure  
1. To prevent a short circuit, remove the key from the ignition and  
disconnect the - battery.  
2. Make the proper input and output wire connections for each unit.  
3. Connect the speaker wires of the wiring harness.  
• After the unit is installed, check whether the brake lamps,  
blinkers, wipers, etc. on the car are working properly.  
4. Connect the wiring harness wires in the following order: ground,  
battery, ignition.  
5. Connect the wiring harness connector to the unit.  
6. Install the unit in your car.  
7. Reconnect the - battery.  
8. Press the reset button.  
— 14 —  
 
Connecting Wires to Terminals  
KENWOOD disc changer control input2  
To connect the Disc changer,  
consult your Disc changer  
manual. 3  
Rear left output (White) 23  
Rear right output (Red) 28  
Fuse (10A) 24  
If no connections are made, do not let  
the wire come out from the tab.  
4
Wiring harness  
(Accessory1)25  
FM/AM antenna input 1  
5 When using the optional power amplifier,  
29  
connect to its power control terminal.  
White/Black  
P.CONT  
Power control wire (Blue/White)  
Motor antenna control wire (Blue)  
To front left  
speaker 30  
7 Depending on what antenna you are using,  
connect either to the control terminal of the  
motor antenna, or to the power terminal for  
the booster amplifier of the film-type  
antenna.  
White  
31  
ANT.CONT  
32  
Gray/Black  
To front right  
speaker 33  
Ignition key  
Gray  
switch  
ACC 13  
34  
35  
10  
Green/Black  
To rear left  
speaker 36  
Ignition wire (Red) 20  
Car fuse  
Green  
box 14  
Car fuse box  
37  
38  
(Main fuse)  
11  
Battery wire (Yellow) 21  
Purple/Black  
To rear right  
speaker 39  
Ground wire (Black) · (To car chassis) 22  
Purple  
40  
Battery 12  
— 15 —  
 
Installation  
Installation  
Installing in Japanese-Made Cars  
1 Refer to the section "Removing the hard rubber frame" (page 17)  
and then remove the hard rubber frame.  
Firewall or metal support  
2 Align the holes in the unit (two locations on each side) with the  
vehicle mounting bracket and secure the unit with the accessory  
screws.  
Screw (M4X8)  
(commercially  
available)  
N
T
8 mm  
8mm  
MAX.  
MAX.  
N
T/N  
3
T
4
ø5mm  
ø5mm  
Bend the tabs of the  
mounting sleeve  
with a screwdriver or  
similar utensil and  
attach it in place.  
T: Toyota cars  
N: Nissan cars  
Accessory3...for Nissan car  
Accessory4 ...for Toyota car  
• During installation, do not use any screws except for those provided.  
The use of different screws might result in damage to the main unit.  
• Damage may occur if a screwdriver or similar tool is used with  
excessive force during the installations.  
Metal mounting strap  
(commercially available)  
Self-tapping screw  
(commercially available)  
Make sure that the unit is installed securely in place. If the unit is  
unstable, it may malfunction (for example, the sound may skip).  
Screwing the Faceplate on the Unit  
If you want to fasten the  
faceplate to the main unit so  
that it does not fall off,  
screw in the provided screw  
(ø4 X 16 mm) in the hole  
shown below.  
Accessory5  
Never insert the taptite screw (ø4 × 16 mm) in any other screw hole  
than the one specified. If you screw it in another hole, it will contact  
and may cause damage to the mechanical parts inside the unit.  
— 16 —  
 
Installation  
Removing the hard rubber frame  
Removing the Unit  
1 Refer to the section “Removing the hard rubber frame” and then  
remove the hard rubber frame.  
1 Engage the catch pins on the removal tool and remove the two  
locks on the lower level.  
Lower the frame and pull it forward as shown in the figure.  
2 Remove the screw (M4 × 8) on the back panel.  
3 Insert the two removal tools deeply into the slots on each side,  
as shown.  
Catch  
Lock  
Accessory2  
Screw (M4X8)  
Removal tool  
(commercially  
available)  
Accessory2  
Removal tool  
2 When the lower level is removed, remove the upper two  
locations.  
4 Lower the removal tool  
toward the bottom, and pull  
out the unit halfway while  
pressing towards the inside.  
Be careful to avoid injury from  
the catch pins on the removal  
tool.  
5 Pull the unit all the way out  
with your hands, being  
careful not to drop it.  
The frame can be removed from the top side in the same manner.  
— 17 —  
 
Troubleshooting Guide  
What might seem to be a malfunction in your unit may  
just be the result of slight misoperation or miswiring.  
Before calling service, first check the following table  
for possible problems.  
? Even if Loudness is turned ON, high-pitched tone isn't compensated  
for. 17  
Tuner source is selected.  
High-pitched tone isn't compensated for when in Tuner source.  
? No sound can be heard, or the volume is low.  
General  
The fader or balance settings are set all the way to one side.21  
Center the fader and balance settings.  
? The power does not turn ON.01  
The input/output wires or wiring harness are connected incorrectly.22  
Reconnect the input/output wires or the wiring harness correctly.  
See the section on "Connecting Wires to Terminals".  
The fuse has blown.  
After checking for short circuits in the wires, replace the fuse with  
one with the same rating.  
The cassette tape is bad.23  
No ACC position on vehicle ignition.02  
Try playing another cassette tape. If works fine, the first tape was  
Connect the same cable to the ignition as the battery cable.  
bad.  
? Nothing happens when the buttons are pressed.04  
? The sound quality is poor or distorted.25  
The computer chip in the unit is not functioning normally.  
Press the reset button on the unit (page 4).  
One of the speaker wires is being pinched by a screw in the car.  
Check the speaker wiring.  
? There’s a source you can’t switch.05  
The tape head is dirty.26  
Clean the tape head.  
There’s no tape inserted.  
Set the media you want to listen to. If there’s no media in this  
unit, you can't switch to each source.  
The speakers are not wired correctly.27  
Reconnect the speaker wires so that each output terminal is  
connected to a different speaker.  
? There’s a source you can’t switch.07  
The Disc changer isn’t connected.08  
Connect the Disc changer. If the Disc changer isn’t connected to  
it's input terminal, You can't switch to an external disc source.  
? The Touch Sensor Tone doesn’t sound.34  
The preout jack is being used.  
The Touch Sensor Tone can’t be output from the preout jack.  
? The faceplate does not open or close.09  
The faceplate is incorrectly attached.  
Reattach the faceplate correctly, See the section on <Removing  
the Faceplate>(page 7).  
? The memory is erased when the ignition is turned OFF.10  
The battery wire has not been connected to the proper terminal.  
Connect the wire correctly, referring to the section on  
<Connecting Wires to Terminals>.  
The ignition and battery wire are incorrectly connected.11  
Connect the wire correctly, referring to the section on  
<Connecting Wires to Terminals>.  
— 18 —  
 
Troubleshooting Guide  
Tuner source  
? Cannot play CD-R or CD-RW.60  
Finalization processing is not being conducted for CD-R/CD-RW.  
? Radio reception is poor.39  
Conduct finalization processing with CD recorder.  
The car antenna is not extended.  
A non-compatible CD changer is being used to play the CD-R/CD-  
RW.61  
Use a CD changer compatible with CD-R/CD-RW to play.  
Pull the antenna out all the way.  
The antenna control wire is not connected.40  
Connect the wire correctly, referring to the section on  
<Connecting Wires to Terminals>.  
?Track Search can't be done.66-2  
For the albums first or last song.  
For each album, Track Search can't be done in the backward  
direction for the first song or in the forward direction for the last  
song.  
Disc source  
? "AVin" is displayed without achieving External disc control mode.50  
O-N switch is set to "O" side.  
Set the switch to "N" side.  
If the following situations, consult your nearest service  
center:  
Unsupported disc changer is connected.  
Connect the supported disc changer. (page 3)  
• Even though the disc changer is connected, the Disc Changer source is  
not ON, with "AVin" showing in the display during the Changer Mode.  
• Even though no device (CA-C1AX) is connected, the Auxiliary input is  
entered when switching modes.  
? The specified disc does not play, but another one plays instead.52  
The specified CD is quite dirty.  
Clean the CD.  
The CD is upside-down.53  
Load the CD with the labeled side up.  
The disc is loaded in a different slot from that specified.54  
Eject the disc magazine and check the number for the specified  
disc.  
The disc is severely scratched.55  
Try another disc instead.  
? The specified track will not play.58  
Random play or magazine random play has been selected.  
Turn off random play or magazine random play.  
? Track repeat, disc repeat, track scan, random play, and magazine  
random play start by themselves.59  
The setting is not canceled.  
The settings for these functions remain on until the setting to off  
or the disc ejected, even if the power is turned off or the source  
changed.  
— 19 —  
 
Troubleshooting Guide  
E-0d:  
The protective circuit in the unit activates when the  
temperature inside the automatic disc changer  
exceeds 60°C (140°F), stopping all operation.E0d  
Cool down the unit by opening the windows or  
turning on the air conditioner. As the temperature  
falls below 60°C (140°F), the disc will start playing  
again.  
The messages shown below display your systems  
condition.  
E-01:  
No disc magazine has been loaded in the changer.  
The disc magazine is not completely loaded.E01  
Load the disc magazine properly.  
E-02:  
E-04:  
No disc has been loaded in the disc magazine.E02  
Load a disc into the disc magazine.  
LOAd:  
Discs are being exchanged in the Disc changer.E57  
No disc has been loaded in the disc magazine.E04  
Load a disc into the disc magazine.  
The CD is quite dirty. The CD is upside-down. The CD  
is scratched a lot.  
2 3 (Blink): The tape player section is not operating properly.E60  
Reinsert the Tape. If the tape cannot be ejected or  
the display continues to flash even when the tape  
has been properly reinserted, please switch off the  
power and consult your nearest service center.  
Clean the CD and load it correctly.  
E-10:  
E-11:  
Nothing has been recorded on the MD.E10  
No tracks are recorded on the MD, although it has a  
title.E11  
E-30:  
E-77:  
The faceplate of the slave unit being connected to  
this unit has been removed.E30  
Replace it.  
The unit is malfunctioning for some reason.E77  
Press the reset button on the unit. If the "E-77"  
code does not disappear, consult your nearest  
service center.  
E-99:  
The unit is malfunctioning for some reason.E99A  
Press the reset button on the unit. If the "E-99"  
code does not disappear, consult your nearest  
service center.  
— 20 —  
 
Specifications  
Specifications subject to change without notice.  
FM tuner section  
Audio section  
Frequency range (50 kHz space) ...............87.5 MHz –108.0 MHz  
(200 kHz space) .............87.9 MHz –107.9 MHz  
Maximum output power.................................................45 W x 4  
Full Bandwidth Power (at less than 1% THD) ................22 W x 4  
Tone action  
Usable sensitivity (S/N = 30dB) ...................9.3 dBf (0.8 µV/75 )  
Quieting Sensitivity (S/N = 50dB) ..............15.2 dBf (1.6 µV/75 )  
Frequency response ( 3.0 dB)..............................30 Hz – 15 kHz  
Signal to Noise ratio (MONO)..............................................70 dB  
Selectivity ( 400 kHz).......................................................80 dB  
Stereo separation (1 kHz) ....................................................40 dB  
Bass : ...............................................................100 Hz 10 dB  
Treble : .............................................................10 kHz 10 dB  
Preout level / Load.............................................1800 mV / 10 kΩ  
Preout impedance............................................................600 Ω  
General  
AM tuner section  
Operating voltage (11 – 16V allowable) ..............................14.4 V  
Current consumption.............................................................10 A  
Installation Size (W x H x D) ..........................182 x 53 x 158 mm  
Weight ................................................................................1.3 kg  
Frequency range (9 kHz space) .....................531 kHz – 1611 kHz  
(10 kHz space) ...................530 kHz – 1700 kHz  
Usable sensitivity (S/N = 20dB) .............................28 dBµ (25 µV)  
Cassette player section  
Tape Speed...............................................................4.76 cm/sec.  
Wow & Flutter (WRMS) ....................................................0.12 %  
Frequency response ( 3.0 dB) (120 µs).................30 Hz – 14 kHz  
Separation (1 kHz) ...............................................................40 dB  
Signal to Noise ratio ............................................................52 dB  
— 21 —  
 

Ingersoll Rand Automobile Parts 650718 C User Manual
Ingersoll Rand Water Pump PD30X X B User Manual
Intellinet Network Solutions Network Router 525312 User Manual
JBL Stereo Amplifier AVA7 User Manual
Jensen Car Speaker JS692 User Manual
JVC Speaker System SP XF20 User Manual
Jwin Headphones i903 User Manual
Kenmore Range 22 92208 User Manual
KitchenAid Dishwasher KUDD03DTBL10 User Manual
Kodak Camera Accessories K7700 User Manual