Belkin Power Supply BU305500 USB User Manual

Lighthouse  
Battery Backup  
BU305500-USB  
User Manual  
 
Introduction  
Package Contents  
1 – USB Cable  
1 – Battery Backup System  
1 – Detachable LED Flashlight  
1 – Phone-Line Cable  
3 – AAA NiMH Batteries  
1 – Installation CD containing Belkin  
Automatic Shutdown Software  
• Incorrect battery connection or replacement  
creates risk of explosion.  
Safety Information  
CAUTION:  
• All batteries used are sealed-lead batteries.  
Batteries should be recycled.  
• Risk of electrical shock—hazardous live  
parts inside. The Unit is energized by the  
battery supply even when the input AC  
power is off.  
System Requirements  
• Risk of electrical shock—do not open  
the case.  
The Lighthouse Battery Backup can be used  
without the software with any computer using  
up to a 17-inch CRT or LCD monitor. You do not  
have to have the software installed to utilize the  
battery-backup outlets.  
• No user-serviceable parts exist inside the  
Unit. Refer repair issues only to qualified  
personnel. Fuses or other parts must be  
replaced ONLY with parts of identical types  
and ratings. Substitution of non-identical  
parts can cause fire and other  
To fully utilize the Unit and its software, your  
computer must be running one of the following  
®
®
operating systems: Windows 98, Me, NT 4,  
2000, 2003, XP, and have a USB port.  
safety hazards.  
• The Unit is intended for installation and  
operation in a controlled environment (a  
temperature-controlled, indoor area free of  
conductive contaminants).  
Features and Functions  
1
2
Battery-Backup Outlets (Fig. 1)  
Surge-Protected-Only Outlets (Fig. 1)  
Only data-sensitive equipment such as a  
computer, monitor, and external drive should  
be plugged into these outlets. Battery power  
is automatically provided in case of a power  
Plug in equipment such as computer  
peripherals, printers, fax machines, or desk  
lamps to these outlets.  
NOTE: These outlets do not provide battery  
outage. Power (AC or battery) is not supplied to power during an outage. The “On/Off” button  
these outlets when the Unit is switched off. (Do does not control these outlets.  
not plug surge protectors or power strips into  
the battery-backup outlets.)  
Do not plug surge protectors or power  
strips into the battery-backup outlets  
Caution: Never connect a laser printer or  
scanner to the backup outlets along with  
other computer equipment. To do so might  
overload the Unit.  
(i.e., daisy-chaining).  
3
AC Circuit Breaker (Fig. 1)  
Should a power overload occur, the circuit  
breaker triggers the Unit to turn off AC power.  
To restore power, depress the “circuit  
breaker” button to reset, then depress the  
“Power” button.  
3
 
Featues and Functions  
4
USB Communication Port (Fig. 1)  
Back Panel (Fig. 1)  
The Unit features a USB communication  
port. Installation of the cable and the Belkin  
Automatic Shutdown Software, which allows  
the Unit to connect to your computer, is  
optional. The Unit will provide backup power  
whether or not the cable and software are  
installed; however, without them you will be  
unable to utilize the data-management  
product features.  
1
2
5
Phone/Fax/Modem Surge Protection  
(Fig. 1)  
The phone/fax/modem lines are  
surge-protected. There are one input jack and  
two output jacks. This allows you to split one  
telephone connection to two separate devices.  
3
4
5
1
Top Panel (Fig. 2)  
Cord-Management Loop (Fig. 2)  
This feature helps to organize and manage the  
power cables from your connected equipment.  
Route all power cables through the loop for a  
clean and organized workspace.  
2
The “On/Off” button has four functions:  
(Fig. 2)  
1
a) Turns on the Unit. Depress button at least  
2 seconds. The green indicator lights.  
b) Cold-start function. If the battery is charged,  
the Unit will work without being plugged into  
an outlet. Depress and hold the key for at least  
2 seconds to turn on the Unit.  
2
3
c) Silence function. During “On Battery Mode”,  
the audible sound can be turned on or off by  
depressing the switch for less than  
1.5 seconds.  
d) Battery-test function. During “On-Line  
Mode”, depressing the switch for less than  
1.5 seconds causes the Unit to perform a  
battery test in backup mode.  
3
Status Indicators (Fig. 2)  
Four LED status lights are located on the  
front panel. The status lights indicate specific  
conditions of the Unit. (See page 5.)  
4
 
Features and Functions  
LED Indicators and Audible Alarms  
AC Power Battery Power  
Fault  
Replace Battery  
The Unit will alarm to indicate certain events.  
Low Battery  
press and hold  
Overload  
Front-Panel  
Label  
Visual  
Indicator  
Audible Alarm  
Description  
AC Power  
AC Power LED  
lights  
None  
The Unit is operating normally on AC power.  
Battery Power  
Battery Power  
LED lights  
Tone every  
10 seconds  
The Unit is operating on battery power.  
The alarm will stop when main AC power  
is returned.  
Low Battery  
Low Battery LED  
flashes  
Tone every  
1 second  
The battery energy is running low. This alarm  
will continue until the Unit performs a forced  
shutdown when the battery is depleted.  
Fault  
Fault LED lights  
Continuous tone  
A fault has occurred. Disconnect all  
equipment from the Unit prior to checking.  
Overload  
Overload LED  
flashes  
Tone every  
1 second  
The Unit is overloaded. Remove connected  
equipment until fault mode is cleared.  
Replace Battery  
Replace Battery  
LED lights  
None  
The battery has reached the end of its useful  
life. The user must replace the battery as  
soon as possible to ensure proper operation  
of the Unit.  
NOTE: The audible alarm will not sound after the alarm is muted.  
and type of batteries. Do not attempt to use  
alkaline or other non-NiMH battery types  
for replacement.  
Flashlight  
The Unit contains a fully functional, detachable  
LED flashlight. The flashlight will automatically  
illuminate when the power goes out. This safety  
function provides an easy way for you to find the  
flashlight while illuminating the area surrounding  
the Unit. The LED flashlight may be removed from  
the Unit to use as a handheld, portable flashlight.  
• Risk of energy hazard. Before replacing  
batteries, remove conductive jewelry such as  
chains, wristwatches, and rings. High energy  
through conductive materials could cause  
severe burns.  
• Do not short-circuit the batteries.  
To remove the LED flashlight from the Unit’s  
recharging dock, pull the top of the LED flashlight  
out and downward until it disengages. When  
not in use, return the LED flashlight to the Unit’s  
recharging dock. The LED flashlight will only  
fit one way in the recharging dock: with the  
flashlight lens pointing toward the top of the Unit  
and the LED flashlight button toward the outside.  
The LED flashlight will only recharge if properly  
docked on the Unit.  
• Carefully install the batteries in the LED  
flashlight housing, ensuring proper polarity.  
Reverse polarity installation may cause  
damage. The battery installation polarity is  
labeled on the LED flashlight housing.  
• Do not heat or incinerate the battery. The  
battery may explode.  
• Only use the UPS Unit to recharge the  
batteries. Charging under other conditions  
can cause the battery to leak, overheat, burst,  
and/or catch fire.  
Flashlight Recharging and Battery Replacement  
CAUTION:  
• The detachable LED flashlight contains 3  
NiMH 700mAh AAA batteries. When replacing  
batteries, replace with the same number  
• Properly dispose or recycle used batteries.  
5
 
Technical Specifications  
Capacity  
550VA/300W  
Battery Overvoltage  
Protection  
Voltage > 15.0V±0.5V  
Input Voltage (Nominal) 120VAC  
LED Flashlight  
Battery Type  
NiMH AAA  
1.2V/700mAh* 3 pcs  
Input Voltage (Range)  
96VAC–135VAC  
60Hz  
Input Frequency  
(Nominal)  
LED Flashlight  
Recharge Time  
(At 25° C) – 8 Hours Recover  
85% Capacity (After Full  
Discharge/Input Voltage  
120VAC)  
Transfer Time (Typical) 10ms (Typical)  
Alerts  
Visual and Audible  
LED Flashlight  
Battery Runtime  
10 hrs @ Full battery charge  
& Amb 25° C  
Input Breaker  
10A/125VAC UL/cUL  
Surge Energy  
Suppression  
700 Joules  
(Total Performance Rated  
With 10*1000µs Pulse)  
Interface/Communication  
Efficiency (AC Mode)  
Waveform  
90% (Input Voltage=120VAC;  
Switching Load=300W)  
Battery Mode  
USB Port  
Modem Protection Single Line (2 Wire, RJ11)  
Jack (In*1; Out*2)  
Step Wave  
(Pseudo Sine-Wave)  
Short-Circuit Protection Shutdown  
(AC Mode)  
Environment  
Short-Circuit Protection Shutdown  
(Backup Mode)  
Operating Temperature 0° C ~ 35° C  
Non-Operating/  
15° C ~ 40° C (With Battery)  
15° C ~ 50° C  
Battery Type  
12V/4.5Ah  
Storage Temperature  
(Without Battery)  
Battery Protection  
30A/32V Fuse *2 pcs  
Operating Humidity  
Audible Noise  
0 ~ 85% RH (Non-Condensing)  
< 42 dBA At 1 Meter  
Recharge Time  
(At 25° C)  
16 Hours Recover  
85% Capacity (After Full  
Loading Discharge /  
Input Voltage 120VAC)  
Battery Run Time  
(90% Full Load)  
1.0 Minutes  
Safety Standards  
(At Temperature 25° C)  
UL/cUL Meets UL 1778/cUL  
EMI Meets FCC Class B  
Battery Run Time  
(Half Load)  
6 Minutes  
(At Temperature 25° C)  
Belkin Tech Support  
Belkin B.V.  
Boeing Avenue 333  
1119 PH Schiphol-Rijk, The Netherlands  
+31 (0) 20 654 7300  
US: 310-898-1100, ext. 2263  
800-223-5546, ext. 2263  
UK: 0845 607 77 87  
Australia: 1800 235 546  
+31 (0) 20 654 7349 fax  
New Zealand: 0800 235 546  
Belkin Ltd.  
4 Pioneer Avenue  
Belkin Corporation  
501 West Walnut Street  
Los Angeles, CA 90220, USA  
310-898-1100  
Tuggerah Business Park  
Tuggerah, NSW 2259, Australia  
+61 (0) 2 4350 4600  
+61 (0) 2 4350 4700 fax  
310-898-1111 fax  
© 2006 Belkin Corporation. All rights reserved.  
All trade names are registered trademarks of respective  
manufacturers listed. Windows and NT are either registered  
trademarks or trademarks of Microsoft Corporation in the United  
States and/or other countries.  
Belkin Ltd.  
Express Business Park, Shipton Way  
Rushden, NN10 6GL, United Kingdom  
+44 (0) 1933 35 2000  
+44 (0) 1933 31 2000 fax  
P75367  
 
Features and Functions  
Flashlight Controls and Functionality  
To turn off the LED flashlight when the light is ON  
in any condition:  
The LED flashlight will automatically turn on in the  
following conditions:  
• press the LED flashlight button.  
when the LED flashlight is on the Unit  
recharging dock and  
NOTE:  
• We ship the LED flashlight without the batteries  
installed. Carefully install the batteries ensuring  
proper polarity, which is labeled on the LED  
flashlight housing. After installing the UPS and  
turning it on, charge the LED flashlight for at  
least 8 hours prior to use.  
• the AC power is removed;  
• the LED flashlight is removed from the dock;  
• the LED flashlight button is pressed.  
when the LED flashlight is removed from the  
Unit recharging dock and  
• During the initial charge period, the LED  
flashlight may not function properly due to low  
battery charge.  
• the LED flashlight button is pressed  
Installation  
NOTE: For maximum benefit, install the  
Unit in an easily accessible location so you  
may detach the flashlight for use. Do not  
place anything on top of the Unit that may  
obscure the control panel or flashlight.  
E. Turning off the Unit  
Turn off your Battery Backup by pressing and  
holding the “On/Off” button for more than  
two seconds until the “AC Power” or “Battery  
Power” LED goes off. The Unit will beep once.  
A. Connect to AC Utility Power  
F. To Conduct a Self-Test  
Plug in the AC cord to a properly grounded wall Use the self-test to verify both the operation  
outlet. Please make sure there are no devices  
plugged into the Unit.  
of the Unit and the condition of the battery. In  
normal utility power, push the “On/Off” button  
for less than 1.5 seconds and the Unit will  
perform a self-test function. During the  
B. Charging the Battery  
For best results, charge the battery for eight  
hours prior to initial use. The Unit charges  
its battery whenever it is connected to the  
utility power.  
self-test, the Unit operates in backup mode.  
NOTE: During the self-test, the Unit briefly  
operates on battery-backup power (the  
“Battery Power” LED comes on). If the Unit  
passes the self-test, it returns to online  
operation. If the Unit fails the self-test, it  
immediately returns to online operation  
and lights the “Replace Battery” LED. The  
loads are not affected. Recharge the battery  
overnight and perform the self-test again.  
If the “Replace Battery” LED is still on, the  
battery needs to be replaced.  
C. Plug in Power Devices  
Plug your devices into the AC outlets on the  
top of the Unit. To use the Unit as a master  
on/off switch, make sure all of the loads are  
switched on.  
Caution: Never connect a laser printer or  
scanner to the backup outlets along with  
other computer equipment. A laser printer  
or scanner draws significantly more power  
when in use than when idle. This may  
overload the Unit.  
G. To Silence Audible Alarm  
While the Unit is in battery-backup mode, push  
the “On/Off” button for less than 1.5 seconds  
to silence the audible alarm. (This does not  
work if the Unit is in a LOW BATTERY or  
OVERLOAD condition.)  
D. Turning on the Unit  
Turn on your Battery Backup by pressing and  
holding the “On/Off” button for longer than two  
seconds until the “AC Power” green light comes  
on. The Unit will beep once.  
All equipment must be powered off prior to  
plugging into the Unit (installation).  
6
 
Installation  
H. Connect the Phone/Fax/Modem Lines  
Connect a single phone/fax/modem line into  
the surge-protected outlets on the back of  
the Unit. The RJ11 modular outlet accepts  
standard single-line telephone connections.  
The connection will require another length of  
telephone cable (included).  
improperly installed. Make sure that the  
telephone line from the wall is plugged into  
the connector marked “IN”, and the device to  
be protected is plugged into the connector  
marked “OUT”.  
I. Connect the USB (Universal Serial Port)  
Communication Port  
NOTE: This connection is optional but highly  
recommended as phone/fax/modem lines  
often carry dangerous surges and spikes.  
The Unit works properly without a  
A USB port is provided to relay the signal to  
support Windows. To fully utilize the Belkin  
Automatic Shutdown software, you will need to  
connect the Unit to your computer. Connect the  
USB cable to the Unit, then connect the other  
end to your computer’s USB port.  
phone/fax/modem connection.  
CAUTION: The phone/fax/modem protection  
feature could be rendered inoperable if  
Battery–Replacement Procedure  
Caution:  
battery to leak, overheat, burst, and/or  
catch fire.  
• The Unit contains a 12V sealed-lead acid  
battery. Replace only with identical battery type, • Properly dispose or recycle used batteries.  
as specified on the factory-installed battery.  
Replacement requires removing the battery  
• Risk of energy hazard. Before replacing  
batteries, remove conductive jewelry such as  
chains, wristwatches, and rings. High energy  
through conductive materials could cause  
severe burns.  
cover plate on the back of the Unit. No tools are  
needed. To replace the batteries:  
1. Press fastener to remove the battery cover  
plate on the back of the Unit.  
2. Disconnect the insulated connectors from the  
battery terminals.  
• Do not short-circuit the battery.  
• Carefully install the batteries in the Unit housing,  
ensuring proper polarity. Reverse polarity  
installation may cause damage.  
3. Remove the battery then insert a new battery  
pack, and push the connectors onto the  
battery terminals (black-to-black and  
• Do not dispose of batteries in a fire. The battery  
may explode.  
red-to-red). WARNING: Misconnection of the  
electrical polarity may result in damage.  
• Do not open or mutilate batteries. Released  
material is harmful to the skin and eyes.  
It may be toxic.  
NOTE: There may be a small spark at the  
battery terminals when reconnecting the  
connectors. This is normal and will not  
harm you or the Unit.  
• Use the UPS Unit only to recharge the batteries.  
Charging under other conditions can cause the 4. Close the battery cover.  
Belkin Automatic Shutdown Software Installation  
occur, and safely shuts down your computer  
in your absence. Please be sure to close all  
applications prior to installing the software.  
Software Installation (Optional)  
A) To fully utilize the Battery Backup and its  
software, your computer must be able to  
operate the following operating systems:  
1.To install the software, place the CD into  
your computer’s CD-ROM drive.  
Windows 98, Me, NT 4, 2000, 2003, or XP,  
and have a USB port.  
2.Your computer should automatically run  
the installation from the CD. If it does not,  
click the “Start” icon on the lower, left-  
hand corner of your screen, and select  
B) Your Battery Backup features the Belkin  
Bulldog Plus Software. This protects and  
saves your data should a power outage  
7
 
Belkin Automatic Shutdown Software Installation  
“Run” from the menu that appears. Enter  
or browse to the CD drive (it may be D).  
Next, double-click “setup.exe” to execute  
the software. Should you continue to have  
Once the “Bulldog Plus Online” screen appears,  
choose “Help”. The “Bulldog Online Help”  
screen will appear. You may use the Contents,  
Index, or Search tabs to assist you with your  
a problem, please refer to your computer’s help issues and to get more information on the  
owner manual to check the designation for specific features and functions of the software.  
your CD-ROM drive.  
C)User Manual Installation  
3.The “Welcome to the Belkin Bulldog Plus  
Product Installation Browser” will appear.  
Please click “Install” and select the  
Windows version.  
You will need Adobe Acrobat Reader to  
review the user manuals. If you do not have  
download a free version of the software.  
4.The “Bulldog Plus Installation” window  
will appear. Please choose the appropriate  
software to install.  
1.From the “Welcome to the Belkin Bulldog  
Plus Product Installation Browser” window,  
locate and choose “User Manuals”.  
5.The InstallShield Wizard will appear  
on-screen. Click “Next”.  
2.The “Bulldog Plus User Manuals” window  
will appear. Please move your pointer to the  
manual you wish to open and click on it.  
6.Please read the User License Agreement  
and click “Yes”.  
3.An Adobe PDF file will be opened. To save  
a copy to your hard drive, you will need to  
go to “File” on your menu bar and choose  
“Save a copy”.  
7.For “Setup Type”, ALL (Standalone) is  
the default. Standalone is for  
battery-backup management for your  
computer only. Networking management  
is for administrators who need to manage  
several battery backups in a workstation  
environment. Do not install the networking  
files unless you are technically qualified to  
use these features. For more information  
on networking, please refer to the software  
user’s manual.  
4.In the “Save a Copy” window, please  
choose a destination folder for the manual.  
D) Uninstall for Windows 98, Me, NT 4, 2000,  
2003, XP  
There are two options for uninstalling the Belkin  
Bulldog Plus Software.  
Option 1  
8.For “Choose Destination Folder”, you have 1. Click on “Start” in the lower, left-hand corner  
the option to choose the location on your  
computer for the software. We recommend  
using the default option as shown  
on-screen. To use the default option,  
click “Next”.  
of your screen and go to the “Programs”  
folder. Scroll to the “Belkin Bulldog Plus”  
folder and choose “Setup”. The InstallShield  
Wizard will appear.  
2. Choose “Remove” and click “Next”.  
9.For “Select Program Folder”, you have the  
option to choose the program folder for  
your software. We recommend using the  
default option as shown on-screen. To use  
the default option, click “Next”.  
3. The “Program Files” and “Audio Files” will  
be checked. If they are not, please check  
them. Click “Next”. The uninstall procedure  
will begin.  
4. Click “Finish” when complete.  
10.In the “Select Language” screen, please  
choose the language you wish to use.  
Option 2  
(Note: Windows 2000, 2003, and XP users, click  
on “Start” and choose “Control Panel”; then go  
to step 2.)  
11.The software will now be installed. Once  
completed, click “Finish”.  
NOTE: Please refer to the help feature found  
on the “Belkin Bulldog Plus Monitor”. To  
access this screen, please click the Belkin  
InstallShield Wizard found in the lower,  
right-hand corner on your taskbar.  
1. Click on “Start” in the lower, left-hand corner  
of your screen, go to “Settings”, and choose  
“Control Panel”.  
8
 
Belkin Automatic Shutdown Software Installation  
2. In Control Panel, locate and click on the  
“Add/Remove Programs” icon. The  
“Add/Remove Programs” window will appear.  
4. Choose “Remove” and click “Next”.  
5. “Program Files” and “Audio Files” will be  
checked. If they are not, please check them.  
Click “Next”. The uninstall procedure  
will begin.  
3. Locate and select the Belkin Bulldog Plus  
Software. Click the “Change/Remove” button  
on the right. InstallShield Wizard will appear.  
6. Click “Finish” when complete.  
Troubleshooting  
PROBLEM  
POSSIBLE CAUSE  
SOLUTION  
Flashlight does not  
turn on or operates  
abnormally  
Flashlight batteries not  
fully charged  
Return the LED flashlight to the Unit  
charging dock and charge for at least  
8 hours.  
Flashlight does not  
charge—Unit charging  
dock not functioning  
1. Make sure the UPS Unit is plugged in  
and turned on.  
2. Clean off the 2 metal contacts on the  
flashlight and the Unit charging dock  
using a dry, lint-free cotton cloth. Do not  
use any liquid to clean these surfaces.  
3. If the LED flashlight does not appear  
to recharge after cleaning the contacts,  
replace the rechargeable NiMH batteries  
using identical replacement batteries.  
Unit not on, LED not lit “On/Off” button not  
pushed or pushed less  
Press the “On/Off” button for more than  
2 seconds  
than 2 seconds  
Battery voltage is too  
low  
Recharge the Unit at least 8 hours  
UPS fault  
Contact service personnel  
(1-800-2 BELKIN)  
Unit always on battery  
mode  
Power cord loose  
Re-plug the power cord  
AC breaker is burned  
out or tripped  
Replace or reset the breaker  
AC utility voltage is  
too high or too low, or  
there is a blackout  
Normal condition  
Backup time too short  
Battery not fully  
charged  
Recharge the Unit at least 8 hours  
The Unit is on overload Remove some unnecessary loads  
Charger fault or other  
reason  
Replace battery;  
The Unit continuously  
beeps  
Overload  
Disconnect non-critical devices  
Red LED lit  
Battery failure  
Replace battery;  
9
 
General Information  
Belkin Corporation (“Belkin”) thanks you for  
choosing one of our products. This User  
License Agreement (“Agreement”) contains the  
terms and conditions under which limited use of  
the product is licensed to you.  
upon such termination you will immediately  
destroy all programs and documentation,  
including all copies made or obtained by you.  
SOFTWARE, PROGRAM, DOCUMENTATION,  
AND ANY RELATED INFORMATION, GOODS  
OR SERVICES ARE PROVIDED WITH NO  
WARRANTY OR REPRESENTATION OF  
ANY KIND WHATSOEVER. BELKIN HEREBY  
DISCLAIMS ALL OTHER WARRANTIES,  
EXPRESSED OR IMPLIED, INCLUDING BUT  
PLEASE READ THIS NOTICE CAREFULLY.  
DO NOT USE THE SOFTWARE OR PRODUCT  
UNTIL YOU HAVE READ AND AGREED  
TO THIS AGREEMENT. IF YOU USE THE  
SOFTWARE AND PRODUCT, YOU ARE  
AGREEING TO THE TERMS AND CONDITIONS NOT LIMITED TO THE IMPLIED WARRANTIES  
SET OUT IN THIS AGREEMENT. IF YOU  
DO NOT ACCEPT THESE TERMS AND  
CONDITIONS, YOU MUST RETURN THE  
UNOPENED PRODUCT WITH THE DISKS  
INSIDE TO THE PARTY FROM WHOM YOU  
RECEIVED IT.  
OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE.  
The entire risk of the use, results and  
performance of the software, program and  
documentation is borne by you. Should any  
or all of the product, software, program,  
documentation, or related information, goods  
or services be defective, misused, unsuitable  
or cause or give rise to any harm or liability  
whatsoever, you, not Belkin or its associates,  
dealers or agents, assume the entire liability,  
cost of repair, correction or any payment or  
other remedy whatsoever. Furthermore, no  
warranty or guarantee is made regarding the  
use or results of the product, software, program,  
documentation, or any related information,  
goods or services in terms of correctness,  
accuracy, reliability, timeliness or otherwise. You  
use and rely on the program at your own risk.  
The following is the only and exclusive warranty  
and remedy of any kind: Belkin does warrant  
that the program disks are free from physical  
defects in materials and workmanship under  
normal use for a period of one (1) year from  
the date of purchase, as evidenced by a copy  
of the sales receipt. Return the defective disk  
or documentation with your receipt directly to  
Belkin for a replacement.  
SCOPE OF USE: In this Agreement,  
software means all machine-readable software  
programs and associated files in this package,  
all modified versions of and upgrades or  
improvements to such programs and all copies  
of such programs and files. You, a single user  
opening this envelope, may use the software  
on a single central processing unit. You may  
not rent it, loan it out, or lease it, nor use it on a  
multiuser system.  
LICENSE: You have the non-exclusive right  
to use the software. You are not permitted  
to copy, modify or transfer the software  
or documentation. You may not compile,  
disassemble or otherwise reverse engineer,  
breakdown, analyze or modify the software.  
USE AND RESTRICTIONS: You are  
permitted to make backup copies of all the  
software disks for archival purposes only.  
You must reproduce the proprietary notice  
set forth on the disks and affix them to all  
backup copies. You are not permitted to use  
these programs in connection with a computer  
service, or to use the backup copies other than  
as a replacement for the original copy.  
DISCLAIMER: Belkin or its associates will  
in no event be liable (i) in any amount for  
lost profits or special, incidental, punitive or  
consequential damages, or (ii) for any claim  
or damage of any nature, or under any theory,  
whatsoever, in any amount in excess of the  
purchase price you paid for the product. The  
warranties and remedies here set forth are  
exclusive, and in lieu of all others oral or written,  
expressed or implied. Some jurisdictions do  
not allow exclusion or limitation of implied  
warranties or of liability for incidental damages,  
so the foregoing limitations or exclusion may  
TERM: This license is effective upon  
acceptance by opening this envelope or in  
any other way using the enclosed software,  
which will constitute your acceptance of, and  
agreement to, this Agreement, and is effective  
until terminated. The limited license in this  
Agreement will be automatically terminated if  
you fail to comply with any of the Terms and  
conditions in this Agreement. You agree that  
10  
 
General Information  
not apply to you. This warranty gives you  
statement of agreement between yourself and  
specific legal rights, which vary from jurisdiction Belkin and supersedes any prior agreements,  
to jurisdiction.  
oral or written, and any other communications  
relating to the subject matter of this Agreement.  
HOWEVER, YOU WAIVE SUCH RIGHTS,  
EXCEPT AS EXPRESSLY PROVIDED UNDER  
THE TERMS AND CONDITIONS OF THIS  
AGREEMENT, TO THE MAXIMUM EXTENT  
ALLOWED BY LAW.  
SEVERABILITY:  
Any term or provision of this Agreement or any  
application thereof, which may be prohibited or  
unenforceable by law in a particular jurisdiction,  
shall be interpreted and enforced to the  
maximum extent allowed in such jurisdiction  
(which the parties acknowledge could mean  
severing the provision from this Agreement or, if  
allowed, enforcing it in a narrower form), without  
affecting the remainder of this Agreement, or  
any other application of such term or provision  
in such jurisdiction, or application of such term  
or provision in any jurisdiction.  
The license is governed by the laws prevailing  
in the State of New York, without regard to its  
conflicts of laws principles.  
ACKNOWLEDGMENT:  
By opening the package on which this  
Agreement is printed, or through which it is  
visible, you acknowledge that you have read  
this Agreement, understand it, and agree that  
this Agreement is the complete and exclusive  
Storage  
Store the Unit covered and upright in a cool,  
dry location with its battery fully charged.  
Before storing, charge the Unit’s battery for  
at least six (6) hours. Disconnect any cables  
connected to the computer interface port to  
avoid unnecessary drainage of the battery.  
Extended Storage  
During extended storage in environments where  
the ambient temperature is +5º F to +86º F,  
charge the Unit’s battery every six (6) months.  
During extended storage in environments where  
the ambient temperature is +86º F to +113º F,  
charge the Unit’s battery every three (3) months.  
Note—Store the Unit:  
Away from sunlight  
Away from heat  
Away from water  
Recycling Information  
Your Battery Backup contains a non-spillable, sealed-lead battery. On the battery, you will find the  
battery name. Please reference the chart below for recycling information.  
Battery Name Recycling Inside the USA  
Recycling Outside the USA  
BB Battery  
(800) 278-8599  
(800) 738-7372  
N/A  
CSB Battery  
1 (817) 244-4415  
VISION Battery (604) 730-2877  
Ritar Battery (888) 841-5179  
N/A  
N/A  
11  
 

BenQ Computer Monitor 9HL8PLBQPA User Manual
BodyCraft Home Gym Strength Training System User Manual
Bolens Lawn Mower 111 330A User Manual
Braun Styling Iron EC 2 User Manual
Briggs Stratton Portable Generator 40204 User Manual
Brinkmann Smoker 810 5503 S User Manual
Carrier Air Conditioner 38AU User Manual
Carrier Refrigerator 1300L User Manual
Chamberlain Work Light 995LM User Manual
Char Broil Gas Grill LP Gas Grill User Manual