Bissell Vacuum Cleaner BS 7920F User Manual

Care and General Maintenance of your Bissell Cleaner  
CONTENTS PAGE  
BS-7920F Pro Heat Pro-Tech………….………………………Page 2  
BS-1694F Powerwash Delux…………………………………..Page 4  
BS-1950F Quickwash…………………………………………..Page 6  
BS- 3750F Lift Off……………………………………………….Page 7  
Prepared by Monique Lania  
1Care & Maintenance of Bissell Deep Cleaner  
 
Cleaning of front window nozzle  
Fill the Tank-in-Tank with clean tap water and fill the SmartMix Bottle with hot (not boiling) tap water.  
Switch grey SmartMix Switch located next to solution SmatMix bottle to  
‘Normal’ and switch diverter knob to ‘Carpet Cleaning’ setting  
Use the machine on hard surface such as concrete to suck up a quantity of clean  
water. This will remove any solution build-up.  
Empty Collection Tank and SmartMix bottle at the end of the procedure.  
For any difficult to remove debris that is trapped in the front window nozzle after flushing the  
machine, it is advisable to use a thin piece of flexible plastic to dislodge the debris.  
Cleaning underneath the front window nozzle  
Wipe underneath surface with a soft cloth  
Ensure after each use that hair and debris are removed from the brush roller using your fingertips or a  
pair of scissors, paying particular attention to the leaver arms. This will prolong the life of the brush  
belt.  
Prepared by Monique Lania  
3Care & Maintenance of Bissell Deep Cleaner  
 
BS-1694F Powerwash Delux  
Cleaning of the Red Lint Filter  
Remove tank-in-tank assembly from unit  
Remove the lid from tank and turn the lid upside down  
Remove red lint basket from tank lid and remove any debris stuck in lint basket with your finger tips or  
an old toothbrush. If it is really dirty soak in hot water for 30 minutes and replace it back into machine  
Once clean the red lint filter basket must be clicked securely in place and sealed to ensure maximum  
suction.  
Prevent solution build up in the machine by flushing the machine after  
cleaning your carpet.  
Fill the Tank-in-Tank with hot (not boiling) tap water and fill the SmartMix Bottle with tap water.  
Switch grey SmartMix Switch located next to solution SmatMix bottle to  
‘Normal’ and switch diverter knob to ‘Carpet Cleaning’ setting  
Use the machine on hard surface such as concrete to suck up a quantity of clean  
water. This will remove any solution build-up.  
Empty collection tank and SmartMix bottle at the end of the procedure.  
Prepared by Monique Lania  
4Care & Maintenance of Bissell Deep Cleaner  
 
Cleaning of front window nozzle  
Fill the Tank-in-Tank with clean tap water and fill the SmartMix Bottle with hot (not boiling) tap water.  
Switch grey SmartMix Switch located next to solution SmatMix bottle to  
‘Normal’ and switch diverter knob to ‘Carpet Cleaning’ setting  
Use the machine on hard surface such as concrete to suck up a quantity of clean  
water. This will remove any solution build-up.  
Empty collection tank and SmartMix bottle at the end of the procedure.  
For any difficult to remove debris that is trapped in the front window nozzle after flushing the  
machine, it is advisable to use a thin piece of flexible plastic to dislodge the debris.  
Cleaning underneath the front window nozzle  
Wipe underneath surface with a soft cloth  
Ensure after each use that hair and debris are removed from the brush roller using your fingertips  
or a pair of scissors, paying particular attention to the leaver arms. This will prolong the life of the  
brush belt.  
Prepared by Monique Lania  
5Care & Maintenance of Bissell Deep Cleaner  
 
BS-1950F Quickwash  
Cleaning Delivery Tank  
Remove delivery tank and thoroughly rinse using hot (not boiling) tap water  
Cleaning underneath the front window nozzle  
Fill delivery tank with clean water only.  
Use machine on concrete to suck up a quantity of clean water.  
Wipe underneath surface with a soft cloth  
Ensure after each use that hair and debris are removed from the brush. This will  
prolong the life of the brush.  
Remove and empty Dirty Water Tank  
Press detent pedal and tip handle back, laying unit flat on the floor  
Release dirty water tank latches (grey latches, 1 on each side of unit) by pulling  
up from the bottom of the latch and then out  
Carefully lift blue dirty water tank from the lower body. Empty tank and rinse  
thoroughly with hot (not boiling) tap water  
Replace blue dirty water tank on lower body of unit and secure with latches  
Prepared by Monique Lania  
6Care & Maintenance of Bissell Deep Cleaner  
 
BS- 3750F Lift Off – Refer to Yellow piece of paper supplied with  
machine  
Empty the clear plastic Dirt Container  
Switch off the cleaner and unplug it from the electrical outlet  
Place vacuum in upright position  
Slide the Lock ‘n Seal Lever to the ‘unlock’ position  
Grasp the handle and pull the Dirt Container straight out to remove from vacuum  
Empty dirt into garbage container  
Rinse plastic container in warm (not boiling), tap water (you can also use a mild  
detergent) and dry thoroughly  
Ensure container is 100% dry before placing back into vacuum  
Put the Dirt Container back in the vacuum and slide Lock ‘n Seal Lever to the ‘lock’ position  
Prepared by Monique Lania  
7Care & Maintenance of Bissell Deep Cleaner  
 
Clean the filters  
1. Upper-tank Filter  
Switch off the cleaner and unplug it from the electrical outlet  
The upper tank filter can be reached by removing the Dirt Container, reaching in underneath the  
Upper Tank and turning the rim of the red Filter Frame to unlock. Pull it straight down to remove.  
Brush the dirt off the Upper Tank and Louvers.  
The foam Upper Tank filter may be removed and hand washed in cold tap water with a mild  
detergent. Rinse well and then air dry thoroughly. **Ensure filter is 100% dry before placing  
back into vacuum  
The Upper Tank and Louvers may be wiped clean using a damp cloth and then dried using a dry cloth.  
**NOTE: For easier access the entire Upper Tank may be removed by turning the red  
knob on the back of the cleaner to ‘unlock’ position and pulling the entire tank straight  
out. Ensure the knob is turned back to ‘lock’ when Upper Tank is replaced back in  
cleaner.  
2. Pre-motor Filter  
Pull out the black slide-out tray located underneath the Dirt Container  
Lift out the foam filter  
The foam filter may be hand washed in cold tap water with a mild detergent.  
Rinse well and then air dry thoroughly. **Ensure filter is 100% dry before placing  
back into vacuum  
Prepared by Monique Lania  
8Care & Maintenance of Bissell Deep Cleaner  
 
3. Hepa 12 Media Post-Motor Filter  
The HEPA Filter is located on the back of the cleaner behind the white door  
Open the door, pulling it downwards, remove the filter and gently tap it against  
the palm of your hand to remove access dust and dirt.  
Replace filter if necessary  
Prepared by Monique Lania  
9Care & Maintenance of Bissell Deep Cleaner  
 

Black Box Headphones HS201A User Manual
Black Decker Video Gaming Accessories ccc3000 User Manual
Blue Rhino Charcoal Grill NBC1712C User Manual
Bosch Power Tools Power Hammer 11222EVSG User Manual
Britax Car Seat Diplomat User Manual
Bushnell Weather Radio 960072C User Manual
Campbell Hausfeld Nail Gun IN727801AV User Manual
Canon Printer Accessories IP 1000 User Manual
Chauvet Stud Sensor IEC 60825 12007 User Manual
Chicago Electric Mixer 65760 User Manual