BlueAnt Wireless Bluetooth Headset Q2 User Manual

SMART  
BLUETOOTH  
HEADSET  
 
User Guide  
Contents  
Introduction  
6
7
Charge Your Q2  
Switching the Q2 On and Off  
Pair the Q2 with your Phone  
Transfer your Phonebook  
Wearing Your Q2  
7
8
8
10  
10  
10  
11  
12  
12  
13  
14  
Changing the Ear Bud  
Stabilizing Ear Buds  
Use Your Voice to Control the Q2  
Use Your Voice to Make Phone Calls  
Use Your Voice to Answer Calls  
Use Your Voice to Access the World  
List of Voice Commands  
 
3
Transferring your Phonebook Contacts to the Q2  
Automatically Transferring your Phonebook Contacts to the Q2  
Manually Transferring your Phonebook Contacts to the Q2  
Updating your Phonebook Contacts on the Q2  
Listening to Audio  
16  
16  
16  
17  
18  
18  
19  
19  
20  
21  
21  
24  
24  
24  
Reconnecting to the Q2  
Using 2 Phones with the Q2 (Multipoint)  
Which Phone is Used for Calls?  
Multiple Calls (Call Waiting)*  
Firmware Upgrades  
Function Reference  
Phone Specific Tips and Tricks  
Android  
Apple® iPhone®  
 
4
BlackBerry  
25  
25  
26  
31  
32  
32  
33  
Other Models  
Troubleshooting  
Resetting the Q2  
Specifications  
Help and Support  
Terms and Conditions  
 
5
Multi-Function  
Button (MFB)  
Introduction  
Welcome to the BlueAnt Q2: the voice controlled smart  
Bluetooth headset for smartphone users.  
Microphones  
With the Q2 you can make outgoing calls and answer  
incoming calls using just your voice, and you will always  
know who is calling without looking at your phone  
because the Q2 will read out the caller’s  
name or number.  
Vol -  
Read on and learn how to use the Q2 to listen to  
turn-by-turn GPS directions, play music, and access  
a world of information such as traffic reports, weather and  
sports results.  
Vol +  
Indicator Light  
 
6
Charge Your Q2  
Your Q2 has been given an initial partial charge to get you started, but for best results we  
recommend you fully charge it using the supplied USB cable and adaptor.  
> You should charge the Q2 whenever it announces that the battery is Very Low.  
> A full charge takes about 3-4 hours.  
> During charging, the indicator light flashes red.  
> When the light goes white, the charge is complete.  
Charging  
port  
Switching the Q2 On and Off  
There is a hardware power switch next to the charging  
port on the back of the Q2.  
Slide the switch across to turn the Q2 on or off.  
Hardware  
power switch  
(off position)  
 
7
Pair the Q2 with your Phone  
To use the Q2 you need to pair it with your phone.  
1. Slide the hardware power switch across to turn the Q2 on and then put the Q2 in your ear.  
2. If this is the first time you have used the Q2 it will go straight to pairing mode. The voice  
prompts will start to talk you through the pairing process.  
For subsequent pairings, click the MFB and wait for the Q2 to ask you to Say A Command.  
Then say Pair Me.  
3. Follow the voice prompts to pair the Q2 with your phone. The pairing code is 0000 (four  
zeros).  
Transfer your Phonebook  
Once the pairing is complete your Q2 will attempt to transfer the contacts from your  
phonebook so that it can announce the names of incoming callers.  
Note: If your phone prompts you to allow a connection to the Q2, you must select “YES” or  
“OK”.  
 
8
BlackBerry®  
Accept connection request  
from BlueAnt Q2?  
If you are using a BlackBerry smartphone you may see a message  
like this one.  
YES  
NO  
Select “Don’t ask this again” so that a tick appears in the box, and  
then choose “YES”.  
Don’t ask this again  
Android™  
Phonebook Access Request  
On Android devices a message about the phonebook transfer may  
appear in the notifications area at the top of the screen.  
Notification  
shown on  
Android  
In order to transfer your contacts you must swipe your finger over this  
message and accept the phonebook transfer request from the Q2.  
devices  
Automatic Transfer Not Supported  
Some phones do not support automatic phonebook transfers. If this is  
the case on your phone the Q2 will announce that it cannot transfer the  
contacts automatically.  
See “Manually Transferring your Phonebook Contacts to the Q2” on page 16 for help.  
 
9
Wearing Your Q2  
You can wear your Q2 in either ear. For best  
results:  
> Rotate the ear gel as shown here.  
> Make sure that the headset is angled towards  
your mouth.  
LEFT  
EAR  
RIGHT  
EAR  
Changing the Ear Bud  
Your Q2 is supplied with a choice of ear buds in different sizes so that you can choose the one  
that fits best. If you want to change the ear bud, remove the attached one by gently lifting it  
away from the Q2.  
Gently press the replacement ear bud onto the Q2 and push it firmly to secure it in place.  
Stabilizing Ear Buds  
The optional stabilizing ear buds allow you to wear the Q2 with or without  
an ear hook. Your Q2 is supplied with a choice of sizes.  
 
10  
Use Your Voice to Control the Q2  
The Q2 is voice controlled. Simply click the MFB and wait for the Q2 to ask you to Say A  
Command.  
Then immediately say one of the voice commands loudly and clearly.  
1
2
3
Phone  
Commands  
Say A  
Command  
 
11  
Use Your Voice to Make Phone Calls  
Click the MFB and wait for the Q2 to ask you to Say A Command, then:  
> Say Phone Commands to activate the voice dial feature on your phone (if your phone  
supports voice dialing).  
> Say Redial to redial the last number you called on your phone.  
> Say Call Back to call back the last call you received on the Q2.  
Use Your Voice to Answer Calls  
When the phone rings, wait for the prompt to ask you if you want to take the call, and then say  
Answer or Ignore. Or:  
> To accept the call click the MFB once.  
> To reject the call double click the MFB.  
During a call, click the MFB to end the call.  
 
12  
Use Your Voice to Access the World  
Your Q2 provides you with voice access to the world by giving you stock quotes, news, sports  
updates, traffic information, weather, and more.  
To access this function:  
1. Click the MFB and wait for the Q2 to ask you to Say A Command.  
2. Say Favorites and wait for the Q2 to ask you Which Favorite?  
3. Say one of the following commands:  
Information  
Sports  
Movies  
Stock Quotes  
Navigate  
Traffic  
News  
Weather  
Note: The availability of Favorites depends on your location and mobile carrier. In the USA,  
this function dials the Bing™ 411 service. Call charges may apply to this call.  
If you are located outside the US, please see www.blueantwireless.com for details on which  
services are available in your location.  
 
13  
List of Voice Commands  
When you want to do something, just click the MFB, wait for the Q2 to ask you to Say A  
Command, and then say one of the following commands:  
> Am I Connected? — The Q2 will check if your phone is connected, and attempt to connect if  
it is not.  
> Call Back — Calls back the last incoming call received on the Q2.  
> Check Battery — Tells you the battery level on the Q2.  
> Favorites — Wait for the Q2 to ask you Which Favorite? then say one of the following:  
Information  
Sports  
Movies  
Stock Quotes  
Navigate  
Traffic  
News  
Weather  
Please Note: The availability of Favorites depends on your location and mobile carrier. Call  
charges may apply.  
> Pair Me — Puts the Q2 into pairing mode. Any connected phone will be disconnected.  
> Phone Commands — Activates your phone’s voice dialing feature (if supported). Depending  
on your phone model, you may need to record voice tags on the phone to use this feature.  
 
14  
> Redial — Redials the last outgoing call made on the connected phone.  
> Sensitivity Level — Configures the sensitivity of the Q2’s voice recognition.  
> LED Light — Turns the LEDs on or off. When the LEDs are set to off, they still light up when  
you turn the Q2 on or off, but will not flash at other times.  
> Update Phonebook — Updates your phonebook contacts on the Q2. If you add contacts to  
your phone, or change the numbers associated with existing contacts, then you will need to  
use this command to transfer the updated contacts to the Q2.  
> What Can I Say? — Reads out a list of all the commands available on the current menu.  
 
15  
Transferring your Phonebook Contacts to the Q2  
Your Q2 uses Text to Speech technology (TTS) to read out the name of the person who is  
calling you. To do this, the Q2 needs to store a copy of your phonebook contacts.  
Automatically Transferring your Phonebook Contacts to the Q2  
When you pair your phone with the Q2 it will attempt to transfer the phonebook contacts  
automatically. The Q2 stores up to 2,000 contacts per phone.  
Tip: If you want to cancel the phonebook transfer, click the MFB.  
Manually Transferring your Phonebook Contacts to the Q2  
Some phones do not support automatic phonebook transfers: if this is the case on your phone  
the Q2 will instruct you to start sending contacts manually. To do this:  
1. Wait to be prompted to start sending contacts to the Q2.  
2. Go to your phonebook and select the contacts you want to send to the Q2. Choose the  
option to “Mark All” or “Select All” if this is available on your phone (if this is not available,  
you will need to transfer each contact individually).  
 
16  
3. Select the option on your phone to “send” or “beam” contacts, business cards, or v-cards  
via Bluetooth, and select the Q2 from the list of Bluetooth devices. See your phone’s  
manual for help with this step.  
Note: some phones do not support phonebook transfers at all. If this is the case, the Q2 will  
read out the caller’s number instead (providing your phone and carrier support caller ID).  
Updating your Phonebook Contacts on the Q2  
If you add or change entries in your phonebook then you need to update the contacts on your  
Q2 by doing the following.  
1. Click the MFB, and wait for the Q2 to ask you to Say A Command.  
2. Say Update Phonebook.  
3. The Q2 will attempt to transfer your phonebook automatically. If this is not possible on your  
phone then you will be prompted to upload the contacts manually.  
 
17  
Listening to Audio  
The Q2 supports A2DP audio streaming. If your phone supports the A2DP profile then  
simply start playing music or any other audio (including turn-by-turn directions from a GPS  
application on your phone) and it will automatically transfer to the Q2.  
If the phone rings the audio will mute. You can use your voice to answer or ignore the call. Or:  
> Click the MFB to accept the call.  
> Double click the MFB to ignore the call.  
The audio will resume when the call ends.  
If you want to exit A2DP streaming mode to do something else, click the MFB. The Q2 will  
ask you to Say A Command. If you do not say a command within a few seconds the music will  
resume playing.  
Reconnecting to the Q2  
If you take your phone out of range of the Q2 for more than 2 minutes, the Q2 will go into  
“sleep mode” to save battery. When you bring your phone back into range, simply click the  
MFB to reconnect.  
 
18  
Alternatively, use the hardware switch to turn the Q2 off whenever you are not using it. The Q2  
will automatically reconnect to your phone if the phone is in range when you switch the Q2 on.  
Depending on your phone, this may take a few seconds. Please ensure that Bluetooth is  
enabled on your phone.  
Using 2 Phones with the Q2 (Multipoint)  
Up to 2 devices can connect to the Q2 at the same time. If either phone rings, you can answer  
it with the Q2.  
Use the Pair Me command to put your Q2 back into pairing mode to pair another phone. Any  
currently connected phone will be disconnected during pairing, so you will need to reconnect  
afterwards.  
Which Phone is Used for Calls?  
When you have two phones connected to the Q2 at the same time you can always answer an  
incoming call on either phone.  
If you initiate a call through the Q2 (for example by saying Phone Commands) then the call  
takes place on the primary phone: the one that connected to the Q2 first.  
 
19  
Note: Only the primary phone can play music through the Q2 via A2DP.  
Multiple Calls (Call Waiting)*  
If you receive an incoming call while you are already on a call the Q2 will play a tone to alert  
you.  
> Hold Vol + for about 1 second to put your current call on hold and answer the incoming call.  
> Hold Vol - for about 1 second to end the current call and answer the incoming call.  
> Once you have a call on hold, you can switch between calls by holding Vol + for about 1  
second.  
Note: If one of the calls ends, some phones do not automatically resume the held call. If this  
happens, hold Vol + for about 1 second to release the hold and resume the other call.  
Tip: If you are using multipoint, both phones remain connected during calls so you can also  
use these controls to switch between calls on both phones.  
* To use this feature, your phone and network must support call waiting.  
 
20  
Firmware Upgrades  
To enhance your experience, we are continually upgrading the Q2 firmware.  
From time to time we will make upgrades available on our website for you to download and  
apply to your Q2. Go to www.blueantwireless.com for full details on the latest upgrades  
available for your Q2.  
You must register your product online at register.blueantwireless.com for access to firmware  
upgrades.  
Function Reference  
> Standby Mode means connected to a device but not on a call.  
> Idle Mode means the Q2 is on but not connected to any devices.  
Q2 Function  
Volume Up  
Do This  
When  
Click Vol +  
Click Vol -  
Idle/Standby/Active call/Music Streaming  
Idle/Standby/Active call/Music Streaming  
Volume Down  
 
21  
Q2 Function  
Do This  
When  
Activate voice control  
Enter pairing mode  
Click the MFB  
Idle/Standby  
Hold the MFB for  
about 1 second  
Idle (not connected to any phones)  
Cancel pairing mode  
Update phonebook  
Click the MFB  
Pairing mode  
Standby  
Hold the MFB for  
about 3 seconds  
Answer a call  
End a call  
Click the MFB  
Click the MFB  
Ringing  
Active call  
Ringing  
Reject a call  
Double click the  
MFB  
Redial  
Hold Vol + for 1  
second  
Standby  
 
22  
Q2 Function  
Do This  
When  
Hold active call and  
switch to incoming or  
held call  
Hold Vol + for 1  
second  
Active call with ringing incoming call or  
held call  
End active call and  
answer a new incoming  
call  
Hold Vol - for 1  
second  
Active call with ringing incoming call  
Call conference  
Hold the MFB for  
about 3 seconds  
Active call with call on hold  
Reset the Q2  
Click Vol +, Vol -  
and the MFB  
together  
Idle (not connected to any phones)  
 
23  
Phone Specific Tips and Tricks  
Android  
> Please note that voice dialing over Bluetooth was added to the Android Operating System in  
version 2.2. It will not be possible to use Phone Commands unless your Android device is  
running Android OS 2.2 or higher.  
> On some Android phones a warning message about the phonebook transfer appears in the  
top left corner. You must select this message and agree to the connection in order to copy  
the phonebook to the Q2.  
Apple® iPhone®  
> Please note that voice control over Bluetooth was introduced on the Apple iPhone 3GS in  
firmware version 3.1. Older versions of the Apple iPhone do not support voice dialing over  
Bluetooth, so it will not be possible to use Phone Commands on these devices.  
> When you transfer your phonebook to the Q2 from the Apple iPhone, the order in which the  
names will be read out is determined by a setting on the phone.  
If you find that the caller’s last name is read out first followed by the caller’s first name then  
 
24  
you should go to the “Settings” menu on your phone, select “Mail, Contacts, Calendars”  
and then change both the “Sort Order” and “Display Order” to “First, Last”. Once you  
have changed this setting, you must use the Update Phonebook command to copy the  
phonebook to the Q2 again.  
BlackBerry  
> When pairing your Q2 with a BlackBerry device, you may be prompted to allow the  
connection from the Q2 in order to transfer your phonebook. If you see a message asking if  
you want to connect to the Q2 or allow a phonebook transfer, choose “Yes” and ensure that  
“Always allow this connection” or “Don’t ask this again” is also selected.  
> If you find that your Q2 does not reconnect to your phone, go to the “Options” menu and  
ensure that the Q2 is configured as a “Trusted Device”.  
Other Models  
For tips and tricks for other phone models, please see our support knowledgebase on  
 
25  
Troubleshooting  
I Cannot Transfer my Phonebook to the Q2  
In order to transfer your phonebook to the Q2, your phone must support either the Phonebook  
Access Profile (PBAP), AT commands, or the Object Push Profile (OPP). If your phone does not  
support any of these Bluetooth profiles, then you will not be able to copy your contacts to the  
Q2. When you receive a call, the Q2 will read out the caller’s number instead (providing your  
phone and carrier support caller ID).  
Some phones support phonebook transfers but do not support doing them automatically. If  
this is the case on your phone then you will need to manually send the contacts to the Q2, as  
described in “Manually Transferring your Phonebook Contacts to the Q2” on page 16.  
If you are having problems transferring your phonebook to the Q2, please see our  
knowledgebase on www.blueantwireless.com. This contains extensive troubleshooting tips  
for phone-specific issues relating to the phonebook transfer process.  
Names Announced in the Wrong Order (Last Name, First Name)  
Depending on how your phone is configured, you may find that the Q2 reads out names the  
wrong way round. If this is happening, you can resolve it by changing the setting on your  
 
26  
phone that controls the display and sort order of your contacts.*  
The exact setting to change depends on your phone. For example, Apple iPhone users should  
go to the “Settings” menu, select “Mail, Contacts, Calendars” and then change both the “Sort  
Order” and “Display Order” to “First, Last”.  
After changing the setting, you must use the Update Phonebook command to update the  
contacts on your Q2.  
* Some phones do not allow you to adjust the order. If this is the case the Q2 will read the  
names in whatever order it receives from the phone.  
The Q2 Does Not Announce the Caller’s Name  
The Q2 will only announce the name if the caller’s name and number are stored in your  
phonebook and have been transferred to the Q2 (on most phones your phonebook is  
automatically transferred when you pair your phone).  
If you make any changes to your phonebook after pairing then you must use the Update  
Phonebook command to update the details on the Q2.  
The Q2 will not read out the caller’s name or number if the caller withholds their number.  
 
27  
The Q2 Reads Out the Wrong Name  
If the Q2 is reading out the wrong name then it is likely that you have changed the contacts  
in your phone without updating the contacts on the Q2. If you make any changes to your  
phonebook, use the Update Phonebook command to copy these changes to the Q2.  
How Many Contacts Can I Store on the Q2?  
The Q2 can store up to 2,000 phone numbers for each paired device.  
Each number stored in your phonebook counts towards this limit. For example, if you have  
a business, home, and mobile number stored for one of your contacts, then this counts as 3  
separate entries.  
My Phone Does Not Reconnect to the Q2  
If your phone always prompts you to confirm whether you want to accept the connection from  
the Q2, then you should configure your phone to treat the Q2 as a “trusted connection” or a  
“trusted device”. The exact option to change will depend on your phone model, but you need  
to go to the Bluetooth menu and locate the Q2 in the list of paired devices, then configure  
the Q2 to be an “authorized device” or add it to your phone’s list of “trusted devices”. If your  
phone has an option to “always allow” the connection or “don’t ask again”, select this option.  
 
28  
My Phone Prompts me for a Code when I Pair the Q2  
Enter the code 0000 (four zeros).  
The Q2 Switches Itself Off  
If the battery gets very low, the Q2 will switch itself off automatically. You should charge the  
Q2 using the supplied USB cable and adaptor.  
The Q2 Does Not Respond to my Voice Commands  
If you are having trouble getting the Q2 to respond to your voice commands, try the following  
tips:  
> Say your command as soon as possible after the Q2 asks you to Say A Command.  
> When you have an incoming call, you must wait for the Q2 to finish asking you if you want to  
Answer or Ignore the call before saying the command.  
> Make sure you say the command clearly, speaking at a consistent speed.  
> If the Q2 does not respond, repeat the command.  
> Speak louder than any background noise.  
 
29  
> Try changing the Q2’s sensitivity level. This setting determines how precisely the words that  
you say need to match the speech patterns that the Q2 has been configured to recognize.  
You can change it by using the Sensitivity Level command.  
The Q2 Played a Tone  
The Q2 plays tones to let you know when certain things happen. If the Q2 played a tone, then  
one of the following has happened:  
> If you take the Q2 out of range of your phone, then it will play a tone to indicate that it is no  
longer connected.  
> The Q2 plays a tone when you end a call.  
> The Q2 plays a call waiting tone if you receive an incoming call while you are on a call.  
The Q2 Light is Distracting  
By default the indicator light on the front of the Q2 will flash at regular intervals to indicate  
that the Q2 is switched on. If you prefer, you can switch this light off. You might want to turn off  
the light if you find it distracting, for example if you are using the Q2 while driving at night.  
Use the LED Light command to turn the light on or off. If you turn the light off, it will still light  
 
30  
up when you turn the Q2 on and off, but not at other times.  
Resetting the Q2  
If you are having problems with the Q2, you can reset it and start again.  
Resetting the Q2 will clear all the stored pairing settings on the Q2, delete any stored contact  
details and put the device back into pairing mode.  
To reset the Q2:  
1. Delete any existing pairing information from your phone and turn the phone off and back on  
again to clear the phone memory.  
2. Make sure the Q2 is switched on but not connected to any phones.  
3. Click Vol +, Vol - and the MFB together. The Q2 will announce that it has been reset.  
4. Now turn the Q2 off and back on again.  
You will now need to pair your phone with the Q2 again.  
 
31  
Specifications  
> Bluetooth version 2.1 + EDR  
> Operating Range: Up to 10 meters  
> Talk Time: Up to 5 hours  
> Supported Profiles: HFP 1.5, A2DP 1.2  
> Frequency: 2.4 GHz  
> Standby Time: Up to 100 hours  
> Battery Type: Rechargeable Lithium Ion  
> Charging Time: 3 - 4 hours  
Help and Support  
If you are having trouble getting the Q2 to work, please visit  
www.blueantwireless.com for online help, support, and troubleshooting  
tips.  
You can also follow the links to register your Q2 for access to firmware  
upgrades.  
Please call us before returning the Q2 to a store and we will help you through any  
difficulty you may have.  
> North America: 1 866 891-3032 > Australia: 1300 669 049 > New Zealand: 0800 443 122  
 
32  
Terms and Conditions  
By using this product, you are agreeing to BlueAnt’s terms and conditions, available at  
www.blueantwireless.com and on the supplied warranty information card.  
Please protect your ears. All BlueAnt devices are designed to reach volumes of up to 100  
decibels. Prolonged use at high volumes may affect your hearing capacity and may result in  
noise induced hearing loss (NIHL). Please read the enclosed safety card for information about  
the safe use of BlueAnt products.  
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG,  
Inc. and any use of such marks by BlueAnt Wireless is under license. Android is a trademark  
of Google Inc., Apple and iPhone are trademarks of Apple Inc., registered in the U.S. and  
other countries. The Trademark BlackBerry® is owned by Research In Motion Limited and is  
registered in the United States and may be pending or registered in other countries. BlueAnt  
Wireless is not endorsed, sponsored, affiliated with or otherwise authorized by Research In  
Motion Limited.  
BlueAnt and other trademarks are trademarks of BlueAnt and other organizations and  
may not be used without permission. The BlueAnt logo is registered in the U.S. Patent and  
Trademark Office and globally with the World Intellectual Property Organization under the  
Madrid protocol.  
© 2010 BlueAnt Wireless. All Rights Reserved.  
Download from Www.Somanuals.com. All Manuals Search VAernsdionD: Qo2-wMnANlo-UaSdE.N-1.0  
33  
 
34  
 
35  
BlueAnt  
North America Australia  
New Zealand Email Enquiries  
1866 891 3032 1300 669 049 0800 443 122 [email protected]  
 

Belkin Computer Accessories F4D153 1 User Manual
Blomberg Dishwasher DW 54100 B User Manual
Braun Electric Shaver EP 80 User Manual
Braun Iron PV 2550 User Manual
BRK electronic Smoke Alarm FCD2BT User Manual
Cabletron Systems Switch 7C03 User Manual
Canon Fax Machine Fax Machine User Manual
Carrier Heat Pump 012 User Manual
Casio Digital Camera QV R41 User Manual
Cavalry Storage Washer Dryer CADA C32A User Manual