Bosch Appliances Security Camera NIN 733 User Manual

FLEXIDOME HD VR  
NIN-733 / NIN-832 / NIN-932  
en Installation Manual  
 
FLEXIDOME HD VR  
Table of Contents | en  
3
Table of Contents  
Safety  
Safety precautions  
Important safety instructions  
Connection in applications  
Type label  
FCC & ICES compliance  
MicroSD cards  
UL certification  
Bosch notices  
Copyrights  
Introduction  
Features  
System Information  
Network video server  
Progressive scan  
True Day/Night function  
Multiple streams  
ONVIF (Open Network Video Interface Forum)  
Audio  
Alarm I/O  
Tamper detection and motion detection  
Video encoding  
Multicast  
Power-over-Ethernet  
Recording  
Configuration  
Operation with external systems  
Planning  
Unpacking  
System requirements  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
4
en | Table of Contents  
FLEXIDOME HD VR  
Installation  
Parts  
Mounting the unit  
Surface mounting  
Flush mount  
Connections  
Make the connections  
Mount the camera  
Controls  
Camera positioning and field-of-view  
Pan  
Tilt  
Twist  
Using the install wizard  
Adjustment procedure  
Closing the unit  
Camera configuration  
User modes  
Day/Night switching  
Browser connection  
Protected network  
Troubleshooting  
Function test  
Resolving problems  
Customer service  
Maintenance  
Testing the network connection  
Cleaning the bubble  
Repairs  
Transfer and disposal  
Technical Data  
Specifications  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
FLEXIDOME HD VR  
Table of Contents | en  
5
Dimensions  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
6
en | Safety  
FLEXIDOME HD VR  
1
Safety  
1.1  
Safety precautions  
DANGER!  
High risk: This symbol indicates an imminently hazardous  
situation such as "Dangerous Voltage" inside the product.  
If not avoided, this will result in an electrical shock, serious  
bodily injury, or death.  
WARNING!  
Medium risk: Indicates a potentially hazardous situation.  
If not avoided, this could result in minor or moderate bodily  
injury.  
CAUTION!  
Low risk: Indicates a potentially hazardous situation.  
If not avoided, this could result in property damage or risk of  
damage to the unit.  
CAUTION!  
The Low Voltage power supply unit must comply with EN/UL  
60950. The power supply must be a SELV-LPS unit or a SELV -  
Class 2 unit (Safety Extra Low Voltage - Limited Power Source).  
CAUTION!  
The camera must be connected to earth.  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
   
FLEXIDOME HD VR  
Safety | en  
7
1.2  
Important safety instructions  
Read, follow, and retain for future reference all of the following  
safety instructions. Follow all warnings on the unit and in the  
operating instructions before operating the unit.  
1. Clean only with a dry cloth. Do not use liquid cleaners or  
aerosol cleaners.  
2. Do not install unit near any heat sources such as radiators,  
heaters, stoves, or other equipment that produce heat.  
Avoid exposure to direct sunlight for long periods.  
3. Never spill liquid of any kind on the unit.  
4. Take precautions to protect the unit from power and  
lightning surges.  
5. Adjust only those controls specified in the operating  
instructions.  
6. Operate the unit only from the type of power source  
indicated on the label.  
7. Unless qualified, do not attempt to service a damaged unit  
yourself. Refer all servicing to qualified service personnel.  
8. Install in accordance with the manufacturer's instructions  
in accordance with applicable local codes. Use only  
attachments/accessories specified by the manufacturer.  
Equipment change or modification could void the user's  
guarantee or authorization agreement.  
9. Connect the yellow/green earth wire of the camera to the  
system earth of the installation to ensure correct safety  
and EMC/RFI protection.  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
 
8
en | Safety  
FLEXIDOME HD VR  
1.3  
Connection in applications  
Grounding  
The yellow/green safety (power) ground wire from the camera  
must be connected to the system earth of the installation.  
U.S.A.: - section 810 of the National Electrical Code, ANSI/NFPA  
No.70, provides information regarding proper grounding.  
12 VDC / 24 VAC power source: This unit is intended to  
operate with a limited power source. The unit is intended to  
operate at either 12 VDC or 24 VAC (if PoE is not available).  
User supplied wiring must be in compliance with electrical  
codes (Class 2 power levels).  
PoE: Use only certified PoE devices. Power-over-Ethernet can  
be connected at the same time as a 12 VDC or 24 VAC power  
supply.  
If auxiliary power (12 VDC or 24 VAC) and PoE are applied  
simultaneously, the camera selects auxiliary input and shuts off  
the PoE.  
1.4  
Type label  
The type label is located on the side of the camera module.  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
   
FLEXIDOME HD VR  
Safety | en  
9
1.5  
FCC & ICES compliance  
FCC & ICES Information  
This equipment has been tested and found to comply with the  
limits for a Class B digital device, pursuant to part 15 of the  
FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference  
to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try  
to correct the interference by one or more of the following  
measures:  
reorient or relocate the receiving antenna;  
increase the separation between the equipment and  
receiver;  
connect the equipment into an outlet on a circuit different  
from that to which the receiver is connected;  
consult the dealer or an experienced radio/TV technician  
for help.  
Intentional or unintentional modifications, not expressly  
approved by the party responsible for compliance, shall not be  
made. Any such modifications could void the user's authority to  
operate the equipment. If necessary, the user should consult  
the dealer or an experienced radio/television technician for  
corrective action.  
The user may find the following booklet, prepared by the  
Federal Communications Commission, helpful: "How to Identify  
and Resolve Radio-TV Interference Problems". This booklet is  
available from the U.S. Government Printing Office,  
Washington, DC 20402, Stock No. 004-000-00345-4.  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
 
10 en | Safety  
FLEXIDOME HD VR  
1.6  
MicroSD cards  
Bosch Security systems recommends that local storage on  
microSD card should only be used for alarm recording and  
Automatic Network Replenishment (ANR) applications. To  
minimize the risk of loss of digital information, we recommend  
multiple, redundant recording systems, and a procedure to  
back up all digital information.  
1.7  
UL certification  
Disclaimer  
Underwriter Laboratories Inc. ("UL") has not tested the  
performance or reliability of the security or signaling aspects of  
this product. UL has only tested fire, shock and/or casualty  
hazards as outlined in UL's Standard(s) for Safety for Information  
Technology Equipment, UL 60950-1. UL Certification does not  
cover the performance or reliability of the security or signaling  
aspects of this product.  
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR  
CERTIFICATIONS WHATSOEVER REGARDING THE  
PERFORMANCE OR RELIABILITY OF ANY SECURITY OR  
SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.  
Disposal - Your Bosch product was developed and  
manufactured with high-quality material and components that  
can be recycled and reused. This symbol means that  
electronic and electrical appliances, which have reached the  
end of their working life, must be collected and disposed of  
separately from household waste material. Separate collecting  
systems are usually in place for disused electronic and  
electrical products. Please dispose of these units at an  
environmentally compatible recycling facility, per European  
Directive 2002/96/EC  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
   
FLEXIDOME HD VR  
Safety | en 11  
1.8  
Bosch notices  
Video loss  
Video loss is inherent to digital video recording; therefore,  
Bosch Security Systems cannot be held liable for any damage  
that results from missing video information. To minimize the  
risk of lost digital information, Bosch Security Systems  
recommends multiple, redundant recording systems, and a  
procedure to back up all analog and digital information.  
Optical elements  
Optical elements are sensitive and should be protected at all  
times. Do not allow objects to come into contact with glass  
surfaces and do not touch optical elements with your fingers.  
Copyright  
This manual is the intellectual property of Bosch Security  
Systems and is protected by copyright.  
All rights reserved.  
Trademarks  
All hardware and software product names used in this  
document are likely to be registered trademarks and must be  
treated accordingly.  
Note  
This manual has been compiled with great care and the  
information it contains has been thoroughly verified. The text  
was complete and correct at the time of printing. The ongoing  
development of the products may mean that the content of the  
user guide can change without notice. Bosch Security Systems  
accepts no liability for damage resulting directly or indirectly  
from faults, incompleteness or discrepancies between the user  
guide and the product described.  
More information  
For more information please contact the nearest Bosch Security  
Systems location or visit www.boschsecurity.com  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
 
12 en | Safety  
FLEXIDOME HD VR  
1.9  
Copyrights  
The firmware uses the fonts "Adobe-Helvetica-Bold-R-Normal--  
24-240-75-75-P-138-ISO10646-1" and "Adobe-Helvetica-Bold-R-  
Normal--12-120-75-75-P-70-ISO10646-1" under the following  
copyright:  
Copyright 1984-1989, 1994 Adobe Systems Incorporated.  
Copyright 1988, 1994 Digital Equipment Corporation.  
Permission to use, copy, modify, distribute and sell this  
software and its documentation for any purpose and without  
fee is hereby granted, provided that the above copyright  
notices appear in all copies and that both those copyright  
notices and this permission notice appear in supporting  
documentation, and that the names of Adobe Systems and  
Digital Equipment Corporation not be used in advertising or  
publicity pertaining to distribution of the software without  
specific, written prior permission.  
This software is based in part on the work of the Independent  
JPEG Group.  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
 
FLEXIDOME HD VR  
Introduction | en 13  
2
Introduction  
2.1  
Features  
The FLEXIDOME HD Vandal-Resistant (VR) IP Day/Night camera  
is a high-performance, surveillance color camera.  
The analog video output of the camera can be used  
simultaneously with an IP stream to allow operation in hybrid  
mode. The IP video stream uses H.264 compression technology  
to give clear images while reducing bandwidth and storage  
requirements. It is also ONVIF compliant to improve  
compatibility during system integration.  
The camera operates as a network video server and transmits  
video and control signals over data networks, such as Ethernet  
LANs and the Internet. The camera is easy to install and ready  
to use. Features include:  
Progressive scan CMOS HD sensor  
Aesthetic vandal-resistant enclosure  
True Day/Night performance with switchable IR filter  
High performance lenses for HD resolution and extra DoF  
Automatic motorized focus and zoom adjustment  
Multiple streams  
MicroSD card slot  
ONVIF conformant  
Two-way audio and audio alarm  
Alarm input and alarm output to external devices  
Intelligent dynamic noise reduction  
Enhanced video motion detection  
Video transmission over IP networks  
Multicast function  
Integrated Ethernet interface (10/100 Base-T)  
Power-over-Ethernet (PoE)  
Password protection  
Integrated Web server for live viewing and configuration via  
a browser  
Firmware update through flash memory  
Hybrid video outputs  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
   
14 en | System Information  
FLEXIDOME HD VR  
3
System Information  
3.1  
Network video server  
The camera incorporates a network video server. Its primary  
function is to encode video and control data for transmission  
over an IP network. With its H.264 encoding, it is ideally suited  
for IP communication and for remote access to digital video  
recorders and IP systems. The use of existing networks means  
that integration with CCTV systems or local networks can be  
achieved quickly and easily. Video images from a single camera  
can be simultaneously received on several receivers.  
3.1.1  
3.1.2  
Progressive scan  
The camera captures and processes progressively scanned  
images. When there is fast motion in a scene, progressively  
scanned images are generally sharper than interlaced images.  
True Day/Night function  
In night mode, the camera enhances low light viewing by  
switching the IR (infrared) filter out of the optical path and  
providing a monochrome image. The camera can switch from  
color to monochrome mode automatically by sensing the  
illumination level, manually via the alarm input, or remotely via a  
web browser.  
3.1.3  
3.1.4  
Multiple streams  
Multiple streams enable the camera to deliver several H.264  
streams together with an M-JPEG stream. These streams  
facilitate bandwidth-efficient viewing and recording options as  
well as integration with third-party video management systems.  
ONVIF (Open Network Video Interface Forum)  
The camera complies to the ONVIF standard which means that  
it is easier to install and integrate into larger systems. The  
ONVIF standard is a global standard for the interface of network  
video products.  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
           
FLEXIDOME HD VR  
System Information | en 15  
3.1.5  
3.1.6  
3.1.7  
Audio  
Two-way duplex audio is available in the unit for live voice  
communications or audio recording.  
Alarm I/O  
The alarm input can be used to control the functionality of the  
unit. An alarm output can control external devices.  
Tamper detection and motion detection  
The camera offers a wide range of configuration options for  
alarm signaling in the event of tampering with the camera. A  
Motion+ algorithm for detecting movement in the video image is  
included.  
3.1.8  
Video encoding  
The camera uses the H.264 compression standards. Thanks to  
efficient encoding, the data rate remains low even with high  
image quality and can also be adapted to local conditions  
within wide limits.  
3.1.9  
Multicast  
In suitably configured networks, the multicast function enables  
simultaneous, real time transmission to multiple receivers. The  
prerequisite for this is that the UDP and IGMP V2/V3 protocols  
are implemented on the network.  
3.1.10  
3.1.11  
Power-over-Ethernet  
Power for the camera can be supplied via a Power-over-  
Ethernet compliant network cable connection. With this  
configuration, only a single cable connection is required to  
view, power, and control the camera.  
Encryption  
The unit offers a variety of options for protection against  
unauthorized reading. Web browser connections can be  
protected using HTTPS. Protect the control channels via the  
SSL encryption protocol. With an additional license, the user  
data itself can be encrypted.  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
             
16 en | System Information  
FLEXIDOME HD VR  
3.1.12  
Recording  
The camera can be used with an iSCSI server connected via the  
network to store long-term recordings, and with a local  
microSD card for shorter storage times and temporary  
recordings.  
3.1.13  
Configuration  
The camera can be configured using a browser on the local  
network (Intranet) or from the Internet. Similarly, firmware  
updates and rapid loading of device configurations are also  
possible. Configuration settings can be stored as files on a  
computer and copied from one camera to another.  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
   
FLEXIDOME HD VR  
System Information | en 17  
3.2  
Operation with external systems  
The camera can be used with a variety of Bosch systems:  
Bosch Video Management System  
Bosch Video Client  
Bosch Recording Station  
When connected to any of these systems, many of the camera  
configuration parameters are controlled by the system and not  
by the settings made via a web browser.  
Bosch Video Management System  
The Bosch Video Management System is a unique enterprise IP  
video surveillance solution that provides seamless management  
of digital video, audio, and data across any IP network. It is  
designed to work with Bosch CCTV products as part of a total  
video surveillance management system.  
Bosch Video Client  
The camera video server and the Bosch Video Client software  
combine to provide a high-performance system solution. The  
Bosch Video Client is a Windows application for viewing,  
operating, controlling, and administering CCTV installations  
(such as surveillance systems) at remote locations.  
Bosch Recording Station  
The camera is also designed for use with the Bosch Recording  
Station. The Bosch Recording Station can record up to 64 video  
and audio streams. The Bosch Recording Station supports  
various functions of the camera, such as controlling relays,  
remote control of peripheral devices, and remote configuration.  
It can use alarm inputs to trigger actions and, when motion  
detection Motion+ is active, can record the relevant cells,  
making intelligent motion detection possible.  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
 
18 en | Planning  
FLEXIDOME HD VR  
4
Planning  
4.1  
Unpacking  
Unpack carefully and handle the equipment with care. The  
packaging contains:  
FLEXIDOME HD VR IP camera  
Torx screwdriver bit  
Camera mounting kit  
Mounting template  
RJ45 female-to-female network cable connector  
Optical disk  
Manuals  
Bosch Video Client  
Quick install instructions and safety instructions  
If equipment has been damaged during shipment, repack it in  
the original packaging and notify the shipping agent or supplier.  
4.2  
System requirements  
Computer with Windows XP/Vista/7 operating system,  
network access, and Microsoft Internet Explorer web  
browser version 9.  
-or-  
Computer with network access and reception software, for  
example Bosch Video Client or Bosch Video Management  
System.  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
     
FLEXIDOME HD VR  
Installation | en 19  
5
Installation  
CAUTION!  
Installation should only be performed by qualified service  
personnel in accordance with the National Electrical Code or  
applicable local codes.  
5.1  
Parts  
The camera/housing unit consists of the following parts:  
1. Surface Mount Box (some models only)  
2. Camera module and mounting base  
3. Inner liner  
4. Dome cover  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
   
20 en | Installation  
FLEXIDOME HD VR  
5.2  
Mounting the unit  
5.2.1  
Surface mounting  
9.5 mm (0.375 in)  
3x  
mm  
8
Ø
3x  
PCD 123 mm (4.84 in)  
To mount the camera on the surface of a wall or ceiling:  
1. Use the surface mount box as a template to mark the holes  
indicated in the drawing. The PCD is 123 mm (4.84 in).  
2. Drill three holes with a diameter of 8 mm (0.3 in).  
3. Insert the supplied plugs into the holes.  
4. Attach the surface mount box securely using the three  
supplied screws.  
5. If you use the side connection of the SMB, remove the cap  
covering the side entrance, otherwise, leave the cap in  
place.  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
   
FLEXIDOME HD VR  
Installation | en 21  
5.2.2  
Flush mount  
105 (4.13)  
3x  
mm  
8
Ø
3x  
57.6  
(2.27)  
57.6  
(2.27)  
PCD: 133 (5.25)  
To flush mount the camera in a wall or ceiling:  
1. Use the mounting template to mark out the recess and to  
mark the holes indicated in the drawing. The PCD is  
133 mm (5.25 in)  
2. Cut out the recess.  
3. Drill three holes with a diameter of 8 mm (0.3 in).  
4. Insert the supplied plugs into the holes.  
5. Partially insert two screws into the mounting holes.  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
 
22 en | Installation  
FLEXIDOME HD VR  
6. Using one of the keyholes, hang the mounting base of the  
camera module on one screw temporarily; tilt the base  
slightly to gain access to the cable connections.  
7. Make the connections as outlined in section 5.3 below.  
5.3  
Connections  
CAUTION!  
Isolate unused power wires individually to prevent short-  
circuits.  
Check the type label on the the camera module for the correct  
power ratings.  
5.3.1  
Make the connections  
Connection box  
The unit has connection terminals on flying leads. In wet or  
outdoor installations make use of a field wiring box with  
NEMA Type 4X or IP66 protection level or better.  
1. Make the connections inside a water tight compartment.  
Isolate unused power wires individually.  
2. After connections are made ensure that the watertight  
compartment is tightly closed and cables and conduits are  
properly sealed to prevent ingress of water.  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
   
FLEXIDOME HD VR  
Installation | en 23  
Cable tree  
Use the following table to identify the wires in the cable tree:  
Wire color  
Red  
AWG  
26  
Signal  
+12 VDC / 24 VAC  
GND DC / 24 VAC  
Brown  
26  
Yellow / Green  
24  
Earth  
Black / Orange  
White / Orange  
White / Violet  
Orange / Violet  
Violet  
28  
28  
28  
28  
28  
28  
28  
28  
28  
Alarm Out A  
Alarm Out B  
Ground (Alarm In)  
Alarm In 1  
Alarm In 2  
White  
Audio In  
(Shield)  
Ground (Audio In)  
Audio Out  
Black  
(Shield)  
Ground (Audio Out)  
For connections use wires of at least the same thickness.  
Power connection  
1. Use a class 2 power supply 24 VAC or +12 VDC.  
2. Connect the power wires (red+ , brown-) to the power  
supply. (Isolate unused power wires individually.)  
3. Connect the earth wire (yellow/green) from the camera to  
the system earth of the installation to ensure correct EMC/  
RFI and safety protection.  
Network (and PoE) connection  
1. Use a shielded twisted pair (STP) Category 5e cable,  
maximum length 100 meters.  
2. Use the RJ45 female-to-female network cable connector to  
connect the network cable of the system to the RJ45  
connector of the camera (Auto MDIX compliant -  
automatically detects the cable connection type).  
Power is supplied to the camera via the Ethernet cable,  
compliant with the Power-over-Ethernet standard.  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
24 en | Installation  
FLEXIDOME HD VR  
CAUTION!  
The RJ45 female-to-female network cable connector supplied is  
unshielded. To comply with the EMC Alarm immunity standard  
(EN 50130-4) or the EMC Railway immunity standard  
(EN 50121-4), a shielded twisted pair (STP) connection cable  
and a shielded RJ45 female-to-female network cable connector  
(not supplied) should be used.  
Analog video output  
Connect to the BNC connector to obtain an analog video signal.  
This is a CVBS 1 Vpp PAL or NTSC signal (depending on the  
selected camera base frequency).  
Note:  
If necessary, use an isolation transformer to avoid ground  
loops.  
Alarm Input  
Use the alarm input to connect external alarm devices such as  
door contacts or sensors. A zero potential make or break  
contact can be used as the actuator (use a bounce-free contact  
system).  
Refer to the cable tree table to identify the wire colors for  
connecting the alarm input.  
Configurable as active low or active high.  
Alarm output  
Use the alarm relay output for switching external devices such  
as lamps or sirens.  
Refer to the cable tree table to identify the wire colors for  
connecting the alarm output.  
In the menu system, configure the relay output to operate  
as either normally open (NO) or normally closed (NC).  
Audio in / Audio out  
The unit has full-duplex mono audio. The two-way  
communication can be used to connect a speaker or door  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
FLEXIDOME HD VR  
Installation | en 25  
intercom system. The audio input signal is transmitted in sync.  
with the video signal.  
Refer to the cable tree table to identify the wire colors for  
connecting the audio input and output.  
Audio in: Line input level (not suitable for direct microphone  
signal).  
Audio out: Line output level (not suitable for direct speaker  
connection).  
Wiring: Shielded audio connection cable is advised.  
5.4  
Mount the camera  
1. Route the cable tree from the camera around the rear of  
the camera module and secure all cables.  
2. Attach the camera module securely using the three  
supplied screws.  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
 
26 en | Installation  
FLEXIDOME HD VR  
5.5  
Controls  
1. Reset button  
Restores the default IP address or  
restores a previous version of the  
firmware if uploading a new version  
fails. With the power on, use a small  
pointed object to press and hold the  
reset button for more than 10  
seconds to restore the factory  
defaults.  
2. Menu button  
Use this button to start the field-of -  
view installation wizard.  
3. MicroSD card slot Insert a microSD card into the slot.  
4. Service video  
output  
2.5 mm jack provides a CVBS signal  
(for installation purposes only)  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
 
FLEXIDOME HD VR  
Installation | en 27  
5.6  
Camera positioning and field-of-view  
The camera module position can be adjusted along three axes  
and several zoom positions can be selected.  
To help position the camera and set the field-of-view:  
1. Connect a monitor to the 2.5 mm jack using the optional  
monitor cable (S1460) which provides a CVBS signal (for  
installation purposes only).  
2. Apply power to the camera.  
3. After power-up, wait a little (about 20 seconds).  
4. Press the Menu button. This stops the IP video stream and  
enables the service video analog output.  
S1460  
FoV  
CAUTION!  
Do not expose the sensors to direct sunlight.  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
   
28 en | Installation  
FLEXIDOME HD VR  
5.6.1  
Pan  
For horizontal adjustment (pan):  
1. Rotate the camera module (1) in the base. Do not rotate  
more than 180° in either direction.  
2. Tighten the locking screw (2) with the supplied  
screwdriver bit.  
5.6.2  
Tilt  
For vertical adjustment (tilt):  
1. Loosen the two thumbwheels (1).  
2. Swing the camera module between the wings. Do not  
rotate more than 90°.  
3. Tighten the two thumbwheels (1).  
≤90°  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
   
FLEXIDOME HD VR  
Installation | en 29  
5.6.3  
Twist  
To obtain a horizontal horizon (for tilted ceilings or sidewall  
mounting), twist the camera module to align the picture shown  
on the monitor.  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
 
30 en | Installation  
FLEXIDOME HD VR  
5.7  
Using the install wizard  
The Menu button on the control panel is used to access the  
camera install wizard. When there is a choice in the wizard, the  
options are selected by either a short press (less than 2 s) or a  
long press (more than 2 s) of the button.  
The wizard handles the following functions:  
Lens identification  
Image orientation  
Zoom and focus adjustment conditions  
Auto focus  
Analog output  
Run the wizard to select orientation and field-of-view (zoom).  
Note:  
The zoom and focus are adjusted again later (with the dome  
bubble in place) via the web browser. This optimizes picture  
sharpness in both bright and low-level lighting.  
5.7.1  
Adjustment procedure  
If you have set up the camera and pressed the Menu button as  
page 27 then you see the following on the monitor screen:  
Lens type:  
State:  
Focus Indicator: 0  
CONTINUE  
<press short>  
180° ROTATE  
<press long>  
Timeout: 300  
The lens type is identified and shown on the screen.  
The iris is opened to its maximum value.  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
   
FLEXIDOME HD VR  
Installation | en 31  
1. To rotate the image 180°, press and hold the Menu button  
until the image flips.  
2. Briefly press the Menu button to set the start position for  
the automatic motorized focus adjustment.  
You will hear the motorized automatic back focus  
process running.  
The progress is shown on the monitor.  
3. Briefly press the Menu button again and again to scroll  
through the preset zoom positions.  
The selection loops back to the beginning when you  
reach the last one.  
4. When you reach the desired zoom position, use a long  
press of the Menu button to set the zoom position and to  
re-focus.  
5. If the camera is not correctly focussed, press the Menu  
button for a longer time to restart the wizard.  
If the camera is correctly focussed, press the Menu button  
for a short time to change the analog output.  
6. To change the analog output state, press the Menu button  
for a short time.  
Briefly press the Menu button again and again to  
select NTSC on, PAL on or OFF (default).  
7. When the selection is made, use a long press of the Menu  
button to save the results.  
The zoom and focus position is stored.  
The iris is set to its original value.  
The video service output is disabled.  
The BNC video output is set to its selected state.  
Note:  
If the BNC video output is set to On, the second IP stream is  
disabled.  
5.8  
Closing the unit  
When the camera position is set and all adjustments have been  
made, close the unit.  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
 
32 en | Installation  
FLEXIDOME HD VR  
1. Disconnect the service cable from the video jack.  
2. Place the inner liner in position aligning its fin with the  
bracket on the base.  
3. Using the supplied screwdriver bit, secure the dome  
bubble to the camera base by tightening the three screws.  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
FLEXIDOME HD VR  
Camera configuration | en 33  
6
Camera configuration  
The camera normally provides an optimal picture without the  
need for further adjustments. Configuration of the camera is  
carried out via the network using a web browser.  
6.1  
User modes  
The camera has six user modes. These modes contain  
optimized settings for a variety of applications. Select the mode  
most suited to the camera’s function via the web browser  
interface.  
6.2  
Day/Night switching  
The camera is equipped with a motorized IR filter. The  
mechanical IR filter is taken out of the optical path in low-light  
applications.  
The IR filter is controlled either:  
via an alarm input, or  
automatically, based on the observed light levels.  
If Auto switching mode is selected, the camera automatically  
switches the filter depending on the observed light level. The  
switching level is programmable.  
Note:  
When the auto mode is selected and the switching level is set  
to -15, certain borderline scene lighting conditions can cause  
the camera to switch back and forth between day and night  
modes. Set a different switching level to avoid this.  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
     
34 en | Browser connection  
FLEXIDOME HD VR  
7
Browser connection  
A computer with Microsoft Internet Explorer can be used to  
receive live images from the camera, control the camera, and  
replay stored sequences. The camera is configured over the  
network using the browser.  
The configuration options using the menu system of the camera  
itself are limited to setting up the lens and network.  
Note:  
The camera can also be configured using the supplied Bosch  
Video Client or the Bosch Video Management System.  
7.1  
Protected network  
If a RADIUS server is used for network access control (802.1x  
authentication), the camera must be configured first. To  
configure the camera for a Radius network, connect it directly  
to a PC via a crossed network cable and configure the two  
parameters, Identity and Password. Only after these have been  
configured can communication with the camera via the network  
occur.  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
   
FLEXIDOME HD VR  
Troubleshooting | en 35  
8
Troubleshooting  
8.1  
Function test  
The camera offers a variety of configuration options. Therefore,  
check that it works properly after installation and configuration.  
This is the only way to ensure that the camera will function as  
intended in the event of an alarm.  
Your check should include the following functions:  
Can you connect to the camera remotely?  
Does the camera transmit all the data required?  
Does the camera respond as desired to alarm events?  
Is it possible to control peripheral devices, if necessary?  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
   
36 en | Troubleshooting  
FLEXIDOME HD VR  
8.2  
Resolving problems  
The following table is intended to help identify the causes of  
malfunctions and correct them where possible.  
Malfunction  
Possible causes  
Solution  
No image  
Defective camera.  
Connect a local monitor  
to the camera and check  
the camera function.  
transmission to  
remote location.  
Faulty cable connections. Check all cables, plugs,  
contacts and  
connections.  
Incorrect encoder stream Select the H.264 MP SD  
property set for  
connection to hardware  
decoder.  
option on the Encoder  
Streams configuration  
page.  
No connection  
The unit's configuration.  
Check all configuration  
parameters.  
established, no  
image transmission.  
Faulty installation.  
Check all cables, plugs,  
contacts and  
connections.  
Wrong IP address.  
Check the IP addresses  
(terminal program).  
Faulty data transmission Check the data  
within the LAN.  
transmission with ping.  
The maximum number of Wait until there is a free  
connections has been  
reached.  
connection and call the  
transmitter again.  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
 
FLEXIDOME HD VR  
Troubleshooting | en 37  
Malfunction  
Possible causes  
Solution  
No audio  
Hardware fault.  
Check that all connected  
audio units are operating  
correctly.  
transmission to  
remote station.  
Faulty cable connections. Check all cables, plugs,  
contacts and  
connections.  
Incorrect configuration.  
Check audio parameters  
on the Audio  
configuration and  
LIVEPAGE Functions  
pages.  
The audio voice  
Wait until the connection  
is free and then call the  
sender again.  
connection is already in  
use by another receiver.  
The unit does not  
report an alarm.  
Alarm source is not  
selected.  
Select possible alarm  
sources on the Alarm  
sources configuration  
page.  
No alarm response  
specified.  
Specify the desired alarm  
response on the Alarm  
connections  
configuration page; if  
necessary change the IP  
address.  
The unit is not  
Power failure during  
Have the unit checked by  
operational after a  
firmware upload.  
programming by firmware Customer Service and  
file.  
replace if necessary.  
Incorrect firmware file.  
Enter the IP address of  
the unit followed by /  
main.htm in your Web  
browser and repeat the  
upload.  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
38 en | Troubleshooting  
FLEXIDOME HD VR  
Malfunction  
Possible causes  
Solution  
Placeholder with a  
JVM not installed on your Install JVM on your  
red cross instead of computer or not  
computer.  
the ActiveX  
activated.  
components.  
Web browser  
contains empty  
fields.  
Active proxy server in  
network.  
Create a rule in the local  
computer's proxy  
settings to exclude local  
IP addresses.  
The POWER LED is Firmware upload failed.  
Repeat firmware upload.  
red.  
8.3  
Customer service  
If a fault cannot be resolved, please contact your supplier or  
system integrator, or go directly to Bosch Security Systems  
Customer Service.  
The version numbers of the internal firmware can be viewed on  
a special page. Please note this information before contacting  
Customer Service.  
1. In the address bar of your browser, after the unit IP  
address, enter: /version  
for example: 192.168.0.1/version  
2. Write down the information or print out the page.  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
 
FLEXIDOME HD VR  
Maintenance | en 39  
9
Maintenance  
9.1  
Testing the network connection  
The ping command can be used to check the connection  
between two IP addresses. This allows testing whether a device  
is active in the network.  
1. Open the DOS command prompt.  
2. Type ping followed by the IP address of the device.  
If the device is found, the response appears as " Reply from ... ",  
followed by the number of bytes sent and the transmission time  
in milliseconds. Otherwise, the device cannot be accessed via  
the network. This might be because:  
The device is not properly connected to the network.  
Check the cable connections in this case.  
The device is not correctly integrated into the network.  
Check the IP address, subnet mask, and gateway address.  
9.2  
Cleaning the bubble  
The exterior of the bubble is hard coated for extra protection. If  
cleaning becomes necessary, only use cleaning solutions and  
cloths suitable for cleaning safety glass lenses. Dry the bubble  
thoroughly with a dry nonabrasive cloth to prevent water spots.  
Never scrub the bubble with any abrasive material or cleaners.  
Do not use abrasive or highly alkaline cleaners on the  
bubble.  
Do not scrape the bubble with razor blades or other sharp  
instruments.  
Do not use Benzene, Gasoline, Acetone, or Carbon  
Tetrachloride on the bubble.  
Do not clean bubbles in the hot sun or on very hot days  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
     
40 en | Maintenance  
FLEXIDOME HD VR  
9.3  
Repairs  
CAUTION!  
Never open the casing of the unit. The unit does not contain any  
user serviceable parts. Ensure that all maintenance or repair  
work is performed only by qualified personnel (electrical  
engineering or network technology specialists). In case of  
doubt, contact your dealer's technical service center.  
9.3.1  
Transfer and disposal  
The camera should only be passed on together with this  
installation guide. The unit contains environmentally hazardous  
materials that must be disposed of according to law. Defective  
or superfluous devices and parts should be disposed of  
professionally or taken to your local collection point for  
hazardous materials.  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
   
FLEXIDOME HD VR  
Technical Data | en 41  
10  
Technical Data  
10.1  
Specifications  
NIN-932  
Imager  
1/3-inch CMOS HD sensor  
1920 × 1080 pixels  
Image resolution  
Rated supply voltage 24 VAC 50/60 Hz  
12 VDC  
Power-over-Ethernet 48 VDC nominal  
Current consumption 600 mA (12 VDC)  
500 mA (24 VAC)  
175 mA (PoE 48 VDC)  
Minimum illumination 0.25 lx Color, 30 IRE  
Lens 3-9 mm, F1.2  
0.08 lx Mono, 30 IRE  
Minimum illumination 0.45 lx Color, 30 IRE  
Lens 10-23 mm, F1.6 0.15 lx Mono, 30 IRE  
Day/Night  
Color, Mono (IR contrast), Auto  
> 90 dB typical  
Dynamic range  
Noise reduction  
Intelligent Dynamic Noise Reduction (iDNR) with  
separate temporal and spatial adjustments  
BLC  
Off/Auto/IntelligentAE  
White Balance  
ATW, AWB hold and manual (2500 to 10000K)  
Indoor and Outdoor ATW  
Shutter  
Automatic Electronic Shutter (AES)  
Fixed (1/30 [1/25] to 1/150000) selectable  
Default shutter  
Contrast  
On/Off  
enhancement  
Sharpness  
Sharpness enhancement level selectable  
Four independent areas, fully programmable  
Motion+, IVA  
Privacy Masking  
Video Analysis  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
   
42 en | Technical Data  
FLEXIDOME HD VR  
Lens type  
3 to 9 mm or 10 to 23 mm varifocal SR (Super  
Resolution)  
Auto Varifocal (AVF) adjustment  
Automatic iris control  
Controls  
Via web browser or Configuration Manager  
6 pre-defined customizable user modes  
User modes  
LAN interface  
STP, Ethernet 10/100 Base-T, auto-sensing,  
half/full duplex, RJ45  
Video encoding  
protocols  
H.264 (ISO/IEC 14496-10), M-JPEG  
Stream (max.)  
1080p25/30  
IP, IBP, IBBP  
Group of pictures  
Network protocols  
IPv4, IPv6, UDP, TCP, HTTP, HTTPS, RTP, IGMPV2/  
V3, ICMP, RTSP, FTP, Telnet, ARP, DHCP,  
SNTP,SNMP (V1, MIB-II), 802.1x, SMTP, iSCSI,  
UPnP (SSDP)  
Encryption  
TLS 1.0, SSL, AES (optional)  
Analog video  
BNC connector, CVBS (PAL/NTSC), 1 Vpp, 75 Ohm  
Analog video (service 2.5 mm jack, CVBS (PAL/NTSC), 1 Vpp, 75 Ohm,  
only)  
non-protected  
Alarm input  
Non-isolated closing contact  
TTL logic, +5V nominal, +40 VDC max,  
(DC coupled with 22 kOhm pull-up to +3.3 VDC)  
Relay output  
Maximum voltage 30 VAC or +40 VDC  
Maximum 0.5 A continuous, 10 VA  
Audio input  
1 Vrms, impedance 12 kOhm  
1 Vrms, impedance 1.5 kOhm  
Audio output  
Audio standards  
AAC  
G.711, 8kHz sampling rate  
L16, 16kHz sampling rate  
Audio signal-to-noise > 50 dB  
ratio  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
FLEXIDOME HD VR  
Technical Data | en 43  
Memory card slot  
Weight  
Supports SDHC and SDXC microSD cards  
0.84 kg (1.85 lb)  
Environment  
Impact protection  
IP 66, NEMA Type 4X  
IK10  
Operating  
-30 °C to +50 °C (-22 °F to +122 °F)  
temperature  
NIN-832  
Imager  
1/2.7-inch CMOS HD sensor  
1920 × 1080 pixels  
Image resolution  
Rated supply voltage 24 VAC 50/60 Hz  
12 VDC  
Power-over-Ethernet 48 VDC nominal  
Current consumption 500 mA | 600 mA IVA (12 VDC)  
450 mA | 500 mA IVA (24 VAC)  
150 mA | 175 mA IVA (PoE 48 VDC)  
Minimum illumination 0.22 lx Color, 30 IRE  
Lens 3-9 mm, F1.2  
0.05 lx Mono, 30 IRE  
Minimum illumination 0.4 lx Color, 30 IRE  
Lens 10-23 mm, F1.6 0.1 lx Mono, 30 IRE  
Day/Night  
Color, Mono (IR contrast), Auto  
Dynamic range  
Noise reduction  
Digital WDR: 76 dB  
Intelligent Dynamic Noise Reduction (iDNR) with  
separate temporal and spatial adjustments  
BLC  
Off/Auto  
White Balance  
ATW, AWB hold and manual (2500 to 10000K)  
Indoor and Outdoor ATW  
Shutter  
Automatic Electronic Shutter (AES)  
Fixed (1/30 [1/25] to 1/150000) selectable  
Default shutter  
Contrast  
On/Off  
enhancement  
Sharpness  
Sharpness enhancement level selectable  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
44 en | Technical Data  
FLEXIDOME HD VR  
Privacy Masking  
Video Analysis  
Lens type  
Four independent areas, fully programmable  
Motion+, IVA versions  
3 to 9 mm or 10 to 23 mm varifocal SR (Super  
Resolution)  
Auto Varifocal (AVF) adjustment  
Automatic iris control  
Controls  
Via web browser or Configuration Manager  
6 pre-defined customizable user modes  
User modes  
LAN interface  
STP, Ethernet 10/100 Base-T, auto-sensing,  
half/full duplex, RJ45  
Video encoding  
protocols  
H.264 (ISO/IEC 14496-10), M-JPEG  
Stream (max.)  
1080p25/30  
IP, IBP, IBBP  
Group of pictures  
Network protocols  
IPv4, IPv6, UDP, TCP, HTTP, HTTPS, RTP, IGMPV2/  
V3, ICMP, RTSP, FTP, Telnet, ARP, DHCP,  
SNTP,SNMP (V1, MIB-II), 802.1x, SMTP, iSCSI,  
UPnP (SSDP)  
Encryption  
TLS 1.0, SSL, AES (optional)  
Analog video  
BNC connector, CVBS (PAL/NTSC), 1 Vpp, 75 Ohm  
Analog video (service 2.5 mm jack, CVBS (PAL/NTSC), 1 Vpp, 75 Ohm,  
only)  
non-protected  
Alarm input  
Non-isolated closing contact  
TTL logic, +5V nominal, +40 VDC max,  
(DC coupled with 22 kOhm pull-up to +3.3 VDC)  
Relay output  
Maximum voltage 30 VAC or +40 VDC  
Maximum 0.5 A continuous, 10 VA  
Audio input  
1 Vrms, impedance 12 kOhm  
1 Vrms, impedance 1.5 kOhm  
Audio output  
Audio standards  
AAC  
G.711, 8kHz sampling rate  
L16, 16kHz sampling rate  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
FLEXIDOME HD VR  
Technical Data | en 45  
Audio signal-to-noise > 50 dB  
ratio  
Memory card slot  
Weight  
Supports SDHC and SDXC microSD cards  
0.84 kg (1.85 lb)  
IP 66, NEMA Type 4X  
IK10  
Environment  
Impact protection  
Operating  
-30 °C to +50 °C (-22 °F to +122 °F)  
temperature  
NIN-733  
Imager  
1/3-inch CMOS HD sensor  
1280 × 720 pixels  
Image resolution  
Rated supply voltage 24 VAC 50/60 Hz  
12 VDC  
Power-over-Ethernet 48 VDC nominal  
Current consumption 500 mA | 600 mA IVA (12 VDC)  
450 mA | 500 mA IVA (24 VAC)  
150 mA | 175 mA IVA (PoE 48 VDC)  
Minimum illumination 0.017 lx Color, 30 IRE  
Lens 3-9 mm, F1.2  
0.0057 lx Mono, 30 IRE  
Minimum illumination 0.03 lx Color, 30 IRE  
Lens 10-23 mm, F1.6 0.01 lx Mono, 30 IRE  
Day/Night  
Color, Mono (IR contrast), Auto  
Dynamic range  
Noise reduction  
84 dB  
Intelligent Dynamic Noise Reduction (iDNR) with  
separate temporal and spatial adjustments  
BLC  
Off, Auto, IntelligentAE (BLC)  
White Balance  
ATW, AWB hold and manual (2500 to 10000K)  
Indoor and Outdoor ATW  
Shutter  
Automatic Electronic Shutter (AES)  
Fixed (1/30 [1/25] to 1/150000) selectable  
Default shutter  
Contrast  
On/Off  
enhancement  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
46 en | Technical Data  
FLEXIDOME HD VR  
Sharpness  
Sharpness enhancement level selectable  
Privacy Masking  
Video Analysis  
Lens type  
Four independent areas, fully programmable  
Motion+, IVA versions  
3 to 9 mm or 10 to 23 mm varifocal SR (Super  
Resolution)  
Auto Varifocal (AVF) adjustment  
Automatic iris control  
Controls  
Via web browser or Configuration Manager  
6 pre-defined customizable user modes  
User modes  
LAN interface  
STP, Ethernet 10/100 Base-T, auto-sensing,  
half/full duplex, RJ45  
Video encoding  
protocols  
H.264 (ISO/IEC 14496-10), M-JPEG  
Stream (max.)  
720p60  
Group of pictures  
Network protocols  
IP, IBP, IBBP  
IPv4, IPv6, UDP, TCP, HTTP, HTTPS, RTP, IGMPV2/  
V3, ICMP, RTSP, FTP, Telnet, ARP, DHCP,  
SNTP,SNMP (V1, MIB-II), 802.1x, SMTP, iSCSI,  
UPnP (SSDP)  
Encryption  
TLS 1.0, SSL, AES (optional)  
Analog video  
BNC connector, CVBS (PAL/NTSC), 1 Vpp, 75 Ohm  
Analog video (service 2.5 mm jack, CVBS (PAL/NTSC), 1 Vpp, 75 Ohm,  
only)  
non-protected  
Alarm input  
Non-isolated closing contact  
TTL logic, +5V nominal, +40 VDC max,  
(DC coupled with 22 kOhm pull-up to +3.3 VDC)  
Relay output  
Maximum voltage 30 VAC or +40 VDC  
Maximum 0.5 A continuous, 10 VA  
Audio input  
1 Vrms, impedance 12 kOhm  
1 Vrms, impedance 1.5 kOhm  
Audio output  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
FLEXIDOME HD VR  
Audio standards  
Technical Data | en 47  
AAC  
G.711, 8kHz sampling rate  
L16, 16kHz sampling rate  
Audio signal-to-noise > 50 dB  
ratio  
Memory card slot  
Weight  
Supports SDHC and SDXC microSD cards  
0.84 kg (1.85 lb)  
IP 66, NEMA Type 4X  
IK10  
Environment  
Impact protection  
Operating  
-30 °C to +50 °C (-22 °F to +122 °F)  
temperature  
10.1.1  
Dimensions  
Ø158 (6.22)  
Ø95 (3.7)  
mm (in)  
Ø158 (6.22)  
mm (in)  
Bosch Security Systems  
Installation Manual  
AM18-Q0637 | v1.1 | 2013.08  
 
 
48 en | Technical Data  
FLEXIDOME HD VR  
AM18-Q0637 | v1.1 | 2013.08  
Installation Manual  
Bosch Security Systems  
 
 
Bosch Security Systems  
© Bosch Security Systems, 2013  
 

Beltronics Radar Detector STi R User Manual
Bionaire Humidifier BCM658 User Manual
Blackberry Intercom System 43 492 User Manual
Black Box Multi tool MPSH16 D20 120V User Manual
Blodgett Oven MT2136E G User Manual
Bowers Wilkins Speaker 202i User Manual
BRK electronic Smoke Alarm RM3 User Manual
Broan Air Conditioner ERV90HCT User Manual
Cabletron Systems Switch 6H122 16 User Manual
Casio Digital Camera QV 8000SX User Manual