Canon Scanner CR 50 User Manual

Installation Guide  
Please read this manual before operating this scanner.  
 
®
FCC REGULATIONS (For 120V model)  
Check Reader, Model M111101/M111102  
This device complies with Part 15 of the FCC Rules. Operation is subject to the  
following two conditions:  
International ENERGY STAR Office Equipment Program  
®
As an ENERGY STAR Partner, CANON ELECTRONICS INC. has  
determined that this machine meets the ENERGY STAR Program  
®
guidelines for energy efficiency.  
®
(1) This device may not cause harmful interference, and (2) this device must accept  
any interference received, including interference that may cause undesired operation.  
Note: This equipment has been tested and found to comply with the limits for a Class  
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful interference in a residential installation.  
This equipment generates, uses, and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no guarantee that  
interference will not occur in a particular installation. If this equipment does cause  
harmful interference to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
The International ENERGY STAR Office Equipment Program is an  
international program that promotes energy saving through the use  
of computers and other office equipment.  
The program backs the development and dissemination of products with functions  
that effectively reduce energy consumption. It is an open system in which business  
proprietors can participate voluntarily. The targeted products are office equipment,  
such as computers, monitors, printers, fax, machine, copiers, and scanners. The  
standards and logos are uniform among participating nations.  
Important Notice for ENERGY STAR Office Equipment Program.  
This model doesn't provide "setting options" for power management.  
European Union (and EEA) only.  
- Reorient or relocate the receiving antenna.  
This symbol indicates that this product is not to be disposed of with your  
household waste, according to the WEEE Directive (2002/96/EC) and  
your national law. This product should be handed over to a designated  
collection point, e.g., on an authorized one-for-one basis when you buy  
a new similar product or to an authorized collection site for recycling  
waste electrical and electronic equipment (EEE). Improper handling of  
this type of waste could have a possible negative impact on the environment and  
human health due to potentially hazardous substances that are generally associated  
with EEE. At the same time, your cooperation in the correct disposal of this product  
will contribute to the effective usage of natural resources. For more information about  
where you can drop off your waste equipment for recycling, please contact your local  
city office, waste authority, approved WEEE scheme or your household waste disposal  
service. For more information regarding return and recycling of WEEE products,  
- Increase the separation between the equipment and receiver.  
- Connect the equipment into an outlet on a circuit different from that to which the  
receiver is connected.  
- Consult the dealer or an experienced radio/TV technician for help.  
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15  
of FCC Rules.  
Do not make any changes or modifications to the equipment unless otherwise  
specified in the manual. If such changes or modifications should be made, you could  
be required to stop operation of the equipment.  
Canon U.S.A. Inc.  
One Canon Plaza, Lake Success NY 11042, U.S.A.  
Tel. No. (516)328-5000  
RADIO INTERFERENCE REGULATIONS (For 120V models)  
This digital apparatus does not exceed the Class B limits for radio noise emissions  
from digital apparatus as set out in the interference-causing equipment standard  
entitled “Digital Apparatus”, ICES-003 of the Industry Canada.  
(EEA: Norway, Iceland and Liechtenstein)  
Für EMVG  
Dieses Produkt ist zum Gebrauch im Wohnbereich, Geschäfts-und Gewerbebereich  
sowie in Kleinbetrieben vorgesehen.  
RÈGLEMENT SUR LE BROUILLAGE RADIOÉLECTRIQUE (For  
120V models)  
Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux  
appareils numériques de Classe B prescrites dans la norme sur le materiel brouilleur:  
“Appareils Numériques”, NMB-003 édictée par l’Industrie Canada.  
Model Names  
The following names may be provided for the safety regulations in each sales region  
of the Check Reader.  
CR-50: Model M111101  
CR-80: Model M111102  
3
 
Trademarks  
• Canon and the Canon logo are registered trademarks of Canon Inc. in the United  
States and may also be trademarks or registered trademarks in other countries.  
• imageFORMULA is a trademark of CANON ELECTRONICS INC.  
• Microsoft, Windows, Windows XP, Windows Vista, and Windows 7 are registered  
trademarks or trademarks of Microsoft Corporation in the United States and other  
countries.  
• Microsoft product screen shot(s) reprinted with permission from Microsoft  
Corporation.  
• Adobe and Adobe Reader are registered trademarks or trademarks of Adobe  
Systems Incorporated in the United States and other countries.  
• Other product and company names herein are, or may be, the trademarks of their  
respective owners.  
Copyright  
Copyright 2011 by CANON ELECTRONICS INC. All rights reserved.  
No part of this publication may be reproduced or transmitted in any form or by any  
means, electronic or mechanical, including photocopying and recording, or by any  
information storage or retrieval system without the prior written permission of  
CANON ELECTRONICS INC.  
Disclaimers  
The information in this document is subject to change without notice.  
CANON ELECTRONICS INC. MAKES NO WARRANTY OF ANY KIND WITH REGARD TO  
THIS MATERIAL, EITHER EXPRESS OR IMPLIED, EXPECT AS PROVIDED HEREIN,  
INCLUDING WITHOUT LIMITATION, THEREOF, WARRANTIES AS TO  
MARKETABILITY, MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OF  
USE OR NON-INFRINGEMENT. CANON ELECTRONICS INC. SHALL NOT BE LIABLE  
FOR ANY DIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY NATURE,  
OR LOSSES OR EXPENSES RESULTING FROM THE USE OF THIS MATERIAL.  
CANON ELECTRONICS INC. IS NOT LIABLE FOR THE STORAGE AND HANDLING OF  
DOCUMENTS SCANNED WITH THIS PRODUCT, OR THE STORAGE AND HANDLING  
OF THE RESULTING SCANNED IMAGE DATA.  
IF YOU INTEND TO DISCARD THE ORIGINALS OF THE SCANNED DOCUMENTS, YOU  
ARE RESPONSIBLE FOR INSPECTING THE SCANNED IMAGES AND VERIFYING THAT  
THE DATA IS INTACT.  
THE MAXIMUM LIABILITY OF CANON ELECTRONICS INC. UNDER THIS WARRANTY  
IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE  
WARRANTY.  
4
 
INTRODUCTION  
Thank you for purchasing the Canon Check Reader CR-50/80.  
Please read this manual thoroughly before using the machine in order  
to familiarize yourself with its capabilities, and to make the most of its  
many functions.  
Symbols Used in This Manual  
The following symbols are used in this manual to explain procedures,  
restrictions, handling precautions, and instructions that should be  
observed for safety.  
Manuals for the CR-50/80  
WARNING  
The following manuals are provided with the CR-50/80. Be sure to  
read these manuals thoroughly before using the scanner. (The  
Installation Guide and the Operation & Maintenance Guide are  
extracted from the Instructions.) Electronic manual is stored as a PDF  
file on the supplied Setup Disc and requires Adobe Reader to open.  
(You can download Adobe Reader from the Adobe Web site.)  
Indicates a warning concerning operations that may lead to death or  
injury to persons if not performed correctly. To use the machine safely,  
always pay attention to these warnings.  
CAUTION  
Indicates a caution concerning operations that may lead to injury to  
persons, or damage to property if not performed correctly. To use the  
machine safely, always pay attention to these cautions.  
Installation Guide (Supplied with the scanner/Electronic Manual):  
This Manual  
Describes the procedure for setting up the CR-50/80 for scanning. Set  
up the CR-50/80 in accordance with the Installation Guide. For details  
on the CR-50/80, refer to the Instructions (electronic manual).  
IMPORTANT  
Indicates operational requirements and restrictions. Be sure to read  
these items carefully to operate the machine correctly, and avoid  
damaging the machine.  
Operation & Maintenance Guide (Supplied with the scanner/  
Electronic Manual)  
Describes the basic operations for using the CR-50/80,  
troubleshooting, and maintenance. For details on the settings of the  
CR-50/80, refer to the Instructions (electronic manual).  
NOTE  
Indicates a clarification of an operation, or contains additional  
explanations for a procedure. Reading these notes is highly  
recommended.  
Instructions (Electronic Manual)  
Describes how to use the scanner, and includes instructions for  
configuring the scanner settings, as well as handling, maintenance,  
and troubleshooting information.  
5
 
     
Table of Contents  
6
 
Important Safety Instructions  
CAUTION  
Handling  
To avoid damage to the scanner, never place the scanner on an unstable  
or vibrating surface. The scanner may tip or fall over, causing injury.  
WARNING  
Keep all liquids, beverages, or any type of liquid, and clips, staples,  
necklaces, or other metal objects away from the scanner. If you  
accidentally spill liquid or drop a metal object into the scanner, turn  
OFF the power immediately and disconnect the power cord from  
the power outlet. Contact your local authorized Canon dealer or  
service representative to have the scanner serviced.  
Never install the scanner in humid or dusty locations. Doing so may  
cause a fire or electrical shock.  
Never place heavy objects on top of the scanner, as these objects  
may tip or fall over, and cause injury.  
When you remove the power cord, grip it by the power plug head.  
Never attempt to disconnect the power cord from the power outlet  
by pulling on the power cord. Doing so may damage or expose the  
cord’s internal wiring, and cause a fire or electrical shock.  
Keep the area around the power outlet clear of all obstacles so you  
can disconnect the power cord easily at all times.  
Never spill water or volatile solutions (alcohol, benzene, paint thinner)  
into the scanner. Doing so may cause a fire or electrical shock.  
When the scanner is not being used for a long period of time,  
disconnect the power cord from the power outlet.  
Avoid wearing loose fitting clothing, dangling jewelry, long ties, or  
long hair that could become entangled with moving parts, especially  
the rollers that feed paper into the scanner. If such objects become  
entangled, immediately disconnect the power plug from the power  
outlet to stop the scanner.  
Be careful when you are loading a document or clearing a paper  
jam. It is possible that the paper edges may cut your fingers.  
Do not open the Maintenance Cover while the scanner is operating.  
Doing so may result in a malfunction or injury.  
Never install and operate the scanner near flammable substances,  
such as alcohol, paint thinner, benzene, or any other type of volatile  
solution.  
Never damage or modify the power cord, and never place heavy  
objects on the power cord.  
Always make sure that your hands are dry when you are handling  
the power cord or power plug. Never grasp the power plug when  
your hands are wet.  
Never plug the scanner into a multiplug power strip.  
Never bundle, wrap, or tie the power cord around itself or another  
object. Connect the power plug securely into the power outlet.  
Use only the power cord and power plug provided with the scanner.  
Never attempt to disassemble or modify the scanner.  
Never use flammable aerosol products near the scanner.  
Before you clean the scanner, turn the power OFF and disconnect  
the power cord from the power outlet.  
To clean the scanner’s exterior, use a firmly wrung cloth, moistened  
slightly with water or mild detergent. Never use any type of volatile  
solution, such as alcohol, benzene or paint thinner.  
If you hear strange sounds, detect smoke or abnormal heat, sense  
vibration, or smell odd odors around the scanner, turn OFF the  
power switch immediately and disconnect the power cord from the  
power outlet. Contact your local authorized Canon dealer or service  
representative to have the scanner serviced.  
Handle the scanner with care. Avoid shock and vibration to the  
scanner caused by reckless handling. If you suspect the scanner  
has been accidentally damaged, turn OFF the power switch  
immediately and disconnect the power cord from the power outlet.  
Contact your local authorized Canon dealer or service  
representative to have the scanner serviced.  
Do not touch the pins and contacts on the scanner’s connector with  
your hands. Doing so may result in a malfunction.  
Before you move the scanner, always turn OFF the power and  
disconnect the power cord from the power outlet.  
This product emits low level magnetic flux. If you use a cardiac  
pacemaker and feel abnormalities, please be away from this  
product and consult your doctor.  
7
 
     
Disposal  
Power Supply  
When disposing of this scanner, be sure to follow all local ordinances  
and laws or consult with the retailer who sold you the scanner.  
Connect only to a power outlet of the rated voltage and power  
supply frequency (either 120 V, 60 Hz or 220-240 V, 50/60 Hz,  
depending on your region).  
Make sure that the scanner is connected to an independent power  
outlet. Do not plug the scanner into an outlet shared with another  
device. If you use an extension cord, make sure that the extension  
cord is rated for the current requirements of the scanner.  
If you are unsure of anything relating to the power supply, contact  
your local authorized Canon dealer or service representative for  
further information.  
Never place an object on top of the power cord or step on the power  
cord.  
Never bundle the power cord or wrap the cord around an object,  
such as a table leg.  
Installation Location  
For operation, maintenance, and ventilation, make sure that there is  
enough space around the scanner.  
Avoid placing the scanner in the following places. It may cause a  
malfunction and adversely affect the scanner or your computer.  
Places exposed to direct sunlight  
If installation in such places is unavoidable, provide a curtain or  
similar object to shade the scanner.  
Places subject to dust and fumes  
Dust and cigarette fumes adversely affect the components inside  
the scanner.  
Do not tug on the power cord. When you remove the power cord,  
grip it by the power plug head.  
Near running water, a heat source, water vapor, or in an area, such  
as a laboratory exposed to ammonia gas, paint thinner, or other  
volatile chemicals  
Places subject to excessive vibration and shock  
Places subject to rapid changes in temperature or humidity  
Condensation occurring inside the scanner may impair image  
quality. Place the scanner in a room that is within the following  
range:  
Room temperature: 10°C to 32.5°C (50°F to 90.5°F)  
Relative humidity: 20% to 80% RH  
20% to 50% RH when using the imprinter  
Use the recommended operating environment for the ink cartridge  
when using the imprinter.  
Keep the area around the power outlet free of obstacles.  
Connect only to a power outlet of the rated voltage and power  
supply frequency (either 120 V, 60 Hz or 220-240 V, 50/60 Hz,  
depending on your region).  
Do not connect to power outlets with other electrical devices. Also,  
when using an extension cord, make sure that the extension cord is  
rated for the current requirements of the scanner.  
Disassembling and/or reassembling the AC adapter is extremely  
dangerous and should not be attempted under any circumstances.  
Do not place heavy objects on the AC adapter or power cord. Do  
not place the adapter or cords in an area where they are likely to be  
stepped on.  
Do not use the power cord while it is bundled.  
Near electronic equipment or heavy equipment that generates a  
strong magnetic field, such as a speaker, TV, and radio  
Never pull directly on the power cord. To remove the plug from the  
outlet, grasp the plug directly and remove it from the outlet.  
Keep the area around the power plug clear of articles so that the  
power plug can be disconnected in an emergency.  
Use only the AC adapter provided with the product. Do not use the  
scanner’s AC adapter with any other product.  
If you have any questions about the AC adapter, contact your local  
authorized Canon dealer or service representative for further  
information.  
8
 
           
Moving the Scanner  
When you move the CR-50/80, hold it firmly with both hands and carry  
it carefully. Do not hold the scanner by the Eject Stopper. The scanner  
weighs approximately 2 kg (4.4 lb).  
WARNING  
When moving the scanner, be sure to turn OFF the power and  
remove any cables. If the cables are not removed before moving  
the scanner, you may damage the plugs or connector by forcibly  
pulling them out.  
9
 
   
Packaging: What Is in the Box?  
Make sure that you have everything shown below. Check every item  
you have removed from the box. If any items are missing, contact your  
local authorized Canon dealer.  
*1  
Setup Disc  
Power Cord  
CR-50/80  
Marking Labels  
for Thickness  
Adjustment Dial  
USB Cable  
*2  
*2  
User Registration Card  
AC Adapter  
Warranty Card  
Installation Guide  
Operation & Maintenance Guide  
*1 The power cord varies, according to the country of purchase.  
*2 For the United States and Canada only.  
NOTE  
Items included in this package may change without any notice.  
10  
 
       
Preparation Before Use  
This chapter describes how to prepare the scanner to scan  
documents.  
IMPORTANT  
• To have the device drivers installed automatically when the  
computer recognizes the CR-50/80, the software needs to be  
installed before the CR-50/80 is connected to the computer.  
• If you connect the computer and turn ON the CR-50/80 before  
installing the software, the following wizard screen appears. If this  
happens, click [Cancel], turn OFF the CR-50/80, and then install the  
software.  
Setting Up the Scanner  
Perform the following steps to set up the CR-50/80. Refer to the  
section for each step for details about that step.  
1
2
Check your operating environment. (See “Checking Your  
The following wizard screen is an example in Windows 7. When a  
similar wizard screen appears in Windows XP/Vista, click [Cancel].  
Install the Scanning Utility provided with the CR-50/80.  
3
4
5
Connect the scanner to a computer. (See “Connecting the  
Wizard Screen (Windows 7)  
p. 14.)  
Automatically installing the device driver. (See p. 15.)  
The device driver is installed automatically when Windows  
recognizes the CR-50/80.  
11  
 
   
Checking Your Operating Environment  
Installing the Scanning Utility  
The following computer system requirements are recommended for  
using the CR-50/80.  
Follow the instructions below to install the Scanning Utility and the  
dedicated driver.  
Operating Systems:  
NOTE  
• Microsoft Windows XP (32bit) SP3 or later  
• Microsoft Windows XP (64bit) SP2 or later  
• Microsoft Windows Vista (32/64bit) SP1 or later  
• Microsoft Windows 7 (32/64bit)  
The dedicated scanner driver is installed after the Scanning Utility  
has been installed.  
1
Turn ON your computer, and log on to Windows.  
Specifications:  
• CPU: Intel Core2 Duo 1.8 GHz or faster  
• Memory: 1 GB or more  
IMPORTANT  
Be sure to log on as the Administrator.  
• USB 2.0 interface  
Interface Cable  
• Use the cable provided or a Hi-Speed USB 2.0 interface cable to  
connect to the computer’s USB port.  
2
Insert the setup disc into the disk drive.  
This manual assumes that “D” is assigned to your disk drive.  
Precautions for Use in 64-bit Operating Systems  
• The ISIS/TWAIN driver supplied with this product supports scanning  
with 32-bit applications only.  
• Even with 32-bit applications, not all ISIS/TWAIN compliant  
applications are guaranteed to operate.  
• Scanning speed may vary depending on the specifications of your computer.  
IMPORTANT  
• If you use the USB interface that was provided as standard with  
your computer:  
• Use the most recently available USB 2.0 driver provided by  
Microsoft. Contact your local authorized Canon dealer for more  
detailed information.  
3
Click [Start], and then click [All Programs].  
The procedure in Windows XP is different from the ones described  
in this manual. Refer to the Windows XP “Help and Support  
Center” to select [Run].  
• Not all USB interfaces provided as standard with personal  
computers are guaranteed. Contact your local authorized Canon  
dealer for more detailed information.  
• Scanning speeds are slower if your computer’s standard USB  
interface is USB 1.1.  
• You should use the USB cable originally bundled with the scanner  
or a Hi-Speed USB 2.0 compatible cable.  
• If the CPU, memory, interface card, and other specifications do not  
satisfy the installation requirements, the scanning speed may be  
greatly reduced and transmission may take longer.  
• Even if the computer satisfies the recommended specifications, the  
scanning speed may vary, depending on the scan settings.  
12  
 
       
4
Click [Accessories], and then click [Run].  
Connecting the Scanner to a Computer  
The only way to connect the scanner to your computer is with a USB  
cable.  
IMPORTANT  
• Be sure to use the USB cable bundled with the scanner or a Hi-  
Speed USB 2.0 compatible cable with the length less than 5 m.  
• When the application is running, do not turn the scanner OFF or  
unplug the interface cable.  
• Do not connect multiple CR-50/80 scanners to one computer.  
CAUTION  
• Do not turn OFF the scanner or remove the interface cable  
when an application is running.  
• Turn OFF the computer and the scanner before changing the  
cable.  
5
6
Enter “D:\SU80\setup.exe” in the [Open] fields, and then  
click [OK].  
USB Connections  
Connect the scanner and the computer with the cable provided or a  
Hi-Speed USB 2.0 cable.  
Type A Plug  
Type B Plug  
Installation starts.  
USB  
Connector  
Follow the instructions on the screen to complete the  
installation.  
IMPORTANT  
The computer may need to be restarted, after the installation,  
depending on the operating system. If this is necessary, make  
sure to restart the computer.  
NOTE  
Connect the type B plug (square) to the scanner and connect the  
type A plug (flat) to the USB port on the computer.  
13  
 
       
Connecting the Power Cord  
Turning ON and OFF the Power  
Connect the power cord.  
Follow the procedures below to turn the scanner power ON and OFF.  
Make sure to use only the power cord provided with the scanner.  
Turning ON the Power  
1
To turn ON the scanner, slide the Power Switch to the  
right.  
(ON)  
IMPORTANT  
• When you turn ON the power, the power LED lights and remains  
lit.  
• If the scanner does not work, there is a problem with the  
scanner. Turn OFF the power, and contact your local authorized  
Canon dealer or service representative to have the scanner  
serviced.  
WARNING  
When connecting the power cord, follow these precautions.  
Failure to do so may cause a fire or electrical shock.  
• Never grasp the power plug when your hands are wet.  
• Never plug the scanner into a multiplug power strip.  
• Never bundle or tie the power cord around itself or another  
object. Connect the power plug securely into the power outlet.  
• Use only the power cord and power plug provided with the  
scanner.  
WARNING  
If you hear strange sounds, detect smoke or abnormal heat,  
sense a vibration, or smell odd odors around the scanner,  
turn OFF the power immediately and disconnect the power  
cord from the power outlet. Contact your local authorized  
Canon dealer or service representative to have the scanner  
serviced.  
• Before you connect the power cord, make sure to turn OFF the  
power switch.  
• Connect only to a power outlet of the rated voltage and power  
supply frequency (either 120 V, 60 Hz or 220-240 V, 50/60 Hz,  
depending on your region).  
2
Turn ON your computer.  
• Do not plug the scanner into a power outlet shared with another  
device. If you use an extension cord, make sure that the  
extension cord is rated for the current requirements of the  
scanner.  
14  
 
         
Turning OFF the Power  
3
Windows recognizes the CR-50/80 as new hardware, and  
installation starts automatically.  
1
2
Turn OFF your computer.  
To turn OFF the scanner, slide the Power Switch to the  
left.  
(Windows 7)  
NOTE  
The CR-50/80 will be registered as “CANON CR-50 USB” or  
“CANON CR-80 USB” in the Imaging Device directory.  
(OFF)  
CAUTION  
• Wait at least 10 seconds before turning the scanner back  
ON.  
• For your safety, disconnect the power plug from the power  
outlet if you are not using the scanner for a long period of  
time.  
15  
 
       
Preparing the Ink Cartridge  
1
Hook your finger around the open lever and open the  
Maintenance Cover.  
This section describes how to prepare the ink cartridge so that you can  
use the imprinter to print text on scanned documents.  
About the Ink Cartridge  
The ink cartridge is not included with the scanner. Purchase an ink  
cartridge separately, as shown below.  
Manufacturer  
: Hewlett Packard  
Ink Cartridge Blue : C6602B (Canon#3693A002)  
Ink Cartridge Red : C6602R (Canon#3693A003)  
Ink Cartridge Green : C6602G (Canon#3693A004)  
Setting the Ink Cartridge and Adjusting  
the Print Position  
2
3
Remove the Imprinter Cover.  
The ink cartridge needs to be set to print. Set the ink cartridge  
according to the following procedure. You can adjust the print position  
to three different levels.  
IMPORTANT  
• To set the ink cartridge, turn the scanner OFF before removing the  
Maintenance Cover. After the ink cartridge is set, replace the  
Maintenance Cover, and then turn the scanner back ON.  
• Finish up the unpacked ink cartridge as soon as possible. More  
frequent cleaning of the ink cartridge is required if long time elapses  
after unpacking.  
Remove the ink cartridge from its bag.  
Tag  
Ink Jet Nozzle  
Contacts  
16  
 
           
IMPORTANT  
5
Place the ink cartridge shown in the diagram below.  
Do not touch the ink cartridge contacts. This can cause a bad  
electrical contact and reduced print quality.  
4
Grasp the tag and then peel off the tape covering the ink  
jet nozzle.  
CAUTION  
Do not touch the electrical contact on the carriage. Doing so  
may cause a malfunction.  
NOTE  
IMPORTANT  
Do not use more than one cartridge by rotation. If you do so,  
applications cannot check the ink level precisely.  
Do not touch the ink jet nozzle or contacts after peeling off the tag  
and tape.  
6
Push down the ink cartridge until it clicks into place.  
17  
 
If the ink head drops back when installed, the two ink cartridge  
pins will not fit into the holes on the carriage. Push back the ink  
cartridge lock lever a in the direction of the arrow and reset the  
cartridge in the correct position b.  
IMPORTANT  
Make sure that the ink cartridge lock lever locks the ink cartridge  
into the correct position.  
Ink Cartridge  
Holes  
Ink Cartridge  
Pins  
If the cartridge does not  
load properly, see step 7.  
Ink Cartridge Lock Lever  
8
9
Carefully replace the Imprinter Cover.  
7
Squeeze the Print Position Adjustment Lever and move it  
to adjust the print position.  
Gently close the Maintenance Cover until it clicks into  
place.  
Top:  
50.5 mm (1.99") from the bottom edge of the document  
Middle:  
47 mm (1.85") from the bottom edge of the document  
Bottom:  
43.5 mm (1.71") from the bottom edge of the document  
18  
 
Document Feeding and Scanning  
For details on the operations, refer to the Instructions (Electronic  
Manual) on p. 33 or the Operation & Maintenance Guide (Manual) on  
p. 6.  
19  
 
 
Index  
A
D
H
I
M
O
P
R
S
T
U
20  
 
 
CANON ELECTRONICS INC.  
1248, SHIMOKAGEMORI, CHICHIBU-SHI, SAITAMA 369-1892, JAPAN  
CANON U.S.A. INC.  
ONE CANON PLAZA, LAKE SUCCESS, NY 11042, U.S.A.  
CANON CANADA INC.  
6390 DIXIE ROAD, MISSISSAUGA, ONTARIO L5T 1P7, CANADA  
CANON EUROPA N.V.  
BOVENKERKERWEG 59-61, P.O.BOX 2262, 1180 EG AMSTELVEEN, THE NETHERLANDS  
CANON LATIN AMERICA, INC.  
703 WATERFORD WAY, SUITE 400, MIAMI, FL 33126, U.S.A.  
CANON SINGAPORE PTE. LTD.  
1 HARBOUR FRONT AVENUE #04-01, KEPPEL BAY TOWER, SINGAPORE 098632  
CANON HONGKONG COMPANY LTD.  
19TH FLOOR, THE METROPOLIS TOWER, 10 METROPOLIS DRIVE, HUNGHOM, KOWLOON, HONG KONG.  
PUB. CE-IE-832  
© CANON ELECTRONICS INC. 2011  
 

Beko Washer WML 50821 User Manual
Boston Acoustics Speaker System BT1 User Manual
Bowers Wilkins Speaker CC3 User Manual
Bowers Wilkins Speaker CCM 636 User Manual
BRK electronic Carbon Monoxide Alarm SC1000B User Manual
Bush Hog Compact Loader 2247QT User Manual
Canon Scanner CanoScan 3200 User Manual
Cavalier Modem 6381 User Manual
CDA Cooktop HCG 730 User Manual
Chamberlain Door 655501 User Manual