Chicago Electric Cordless Drill 95848 User Manual

18 VOLT CORDLESS DRILL  
Model 95848  
OPERATING INSTRUCTIONS  
Due to continuing improvements, actual product may differ slightly from the product described herein.  
®
3491 Mission Oaks Blvd., Camarillo, CA 93011  
TO PREVENT SERIOUS INjURy, READ  
AND UNDERSTAND ALL WARNINGS AND  
INSTRUCTIONS bEfORE USE.  
Copyright© 2007 by Harbor Freight Tools®. All rights reserved. No portion of  
this manual or any artwork contained herein may be reproduced in any shape  
or form without the express written consent of Harbor Freight Tools.  
 
prong or modify the plug in any way. Do not use any adapter plugs. Check with  
a qualified electrician if you are in doubt as to whether the outlet is properly  
grounded. If the tools should electrically malfunction or break down, grounding  
provides a low resistance path to carry electricity away from the user.  
2.  
3.  
Double insulated tools are equipped with a polarized plug (one blade is wider  
than the other). This plug will fit in a polarized outlet only one way. If the plug  
does not fit fully in the outlet, reverse the plug. If it still does not fit, contact  
a qualified electrician to install a polarized outlet. Do not change the plug  
in any way. Double insulation eliminates the need for the three wire grounded  
power cord and grounded power supply system.  
Avoid body contact with grounded surfaces such as pipes, radiators, ranges,  
and refrigerators. There is an increased risk of electric shock if your body is  
grounded.  
4.  
5.  
Do not expose power tools to rain or wet conditions. Water entering a power  
tool will increase the risk of electric shock.  
Do not abuse the Charger’s power cord. Never use the Power Cord to carry  
the Charger or pull the Plug from an outlet. Keep the Power Cord away from  
heat, oil, sharp edges, or moving parts. Replace damaged Power Cords im-  
mediately. Damaged Power Cords increase the risk of electric shock.  
Personal Safety  
1.  
Stay alert. Watch what you are doing, and use common sense when operat-  
ing a power tool. Do not use a power tool while tired or under the influence  
of drugs, alcohol, or medication. A moment of inattention while operating power  
tools may result in serious personal injury.  
2.  
3.  
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.  
Keep your hair, clothing, and gloves away from moving parts. Loose clothes,  
jewelry, or long hair can be caught in moving parts.  
Avoid accidental starting. be sure the Rotation button (9) is in the locked  
position before inserting the battery. Carrying power tools with your finger on  
the trigger, or inserting the Battery with the trigger depressed, invites accidents.  
4.  
5.  
Do not overreach. Keep proper footing and balance at all times. Proper footing  
and balance enables better control of the power tool in unexpected situations.  
Use safety equipment. Always wear eye protection. Dust mask, nonskid safety  
shoes, hard hat, or hearing protection must be used for appropriate conditions.  
Always wear ANSI-approved safety goggles when working with this tool.  
SKU 95848  
for technical questions, please call 1-800-444-3353.  
PAGE 3  
 
Tool Use and Care  
1.  
Use clamps (not included) or other practical ways to secure and support the  
workpiece to a stable platform. Holding the work by hand or against your body  
is unstable and may lead to loss of control.  
2.  
3.  
4.  
Do not force the tool. Use the correct tool for your application. The correct  
tool will do the job better and safer at the rate for which it is designed.  
Do not use the power tool if the trigger does not operate it. Any tool that cannot  
be controlled with the trigger is dangerous and must be replaced.  
Remove the battery from the tool and set the Rotation button (9) to the cen-  
ter, locked position, before making any adjustments, changing accessories,  
or storing the tool. These preventive safety measures reduce the risk of starting  
the tool accidentally.  
5.  
6.  
Store idle tools out of reach of children and other untrained persons. Tools  
are dangerous in the hands of untrained users.  
Maintain tools with care. Keep drill bits (not included) sharp and clean. Prop-  
erly maintained accessories with a sharp cutting edge are less likely to bind and  
are easier to control. Do not use a damaged tool or accessory. Tag damaged tools  
“Do not use” until repaired.  
7.  
8.  
Check for misalignment or binding of moving parts, breakage of parts, and any  
other condition that may affect the tool’s operation. If damaged, have the tool  
serviced before using. Many accidents are caused by poorly maintained tools.  
Use only accessories that are recommended by the manufacturer for your  
model. Accessories that may be suitable for one tool may become hazardous  
when used on another tool.  
Service  
1.  
2.  
Tool service must be performed only by qualified repair personnel. Service or  
maintenance performed by unqualified personnel could result in a risk of injury.  
When servicing a tool, use only identical replacement parts. follow instruc-  
tions in this manual. Use of unauthorized parts or failure to follow maintenance  
instructions may create a risk of electric shock or injury.Specific Safety Rules  
SPECIfIC SAfETy RULES  
1.  
Maintain a safe working environment. Keep the work area well lit. Make sure  
there is adequate surrounding workspace. Always keep the work area free of  
obstructions, grease, oil, trash, and other debris. Do not use the Cordless Drill in  
SKU 95848  
for technical questions, please call 1-800-444-3353.  
PAGE 4  
 
areas near flammable chemicals, dusts, and vapors. Do not use this product in a  
damp or wet location.  
2.  
Maintain labels and nameplates on the Cordless Drill. These carry important  
information. If unreadable or missing, contact Harbor Freight Tools for a replace-  
ment.  
3.  
4.  
When using the Cordless Drill, always maintain a firm grip on the tool with  
both hands.  
Hold the tool by its insulated gripping surfaces when performing an operation  
where the Cordless Drill may contact hidden wiring. Contact with a “live” wire  
will make exposed metal parts of the Cordless Drill “live” and shock the operator.  
5.  
6.  
Do not use the Cordless Drill or Charger (29) if it has been dropped, damaged,  
left outdoors, or immersed in liquid.  
To avoid electric shock, do not pull or carry the Charger by its Power Cord or  
pull the Power Cord around sharp corners or edges. Do not unplug the Charger  
by pulling on the Power Cord. Keep the Power Cord away from heated surfaces.  
7.  
To avoid electrical shock, do not handle the Charger, the Adapter (30), or the  
Cordless Drill with wet hands.  
8.  
Keep the Handles of the Cordless Drill dry, clean, and free from oil or  
grease.  
9.  
Avoid unintentional starting. Make sure you are prepared to begin work before  
turning on the Cordless Drill.  
10.  
11.  
Never leave the Charger unattended when it is plugged into an electrical outlet.  
Unplug the Charger from its electrical outlet before leaving.  
PROPER bATTERy PACK CARE: battery Pack (28) leakage may occur under  
extreme usage or temperature conditions. If Battery Pack fluid comes in contact  
with skin, rinse with lemon juice and vinegar then wash with soap and water. If the  
fluid comes into contact with the eyes, flush with water for several minutes and contact  
a doctor immediately. Never burn the Battery Pack, as it can explode in a fire. Do  
not charge the Cordless Drill with a leaking Battery Pack. Contact local solid waste  
authorities for instructions on correct disposal or recycling of the Battery Pack.  
12.  
WARNING! Some dust created by power sanding, sawing, grinding, drilling, and  
other construction activities, contain chemicals known (to the State of California) to  
cause cancer, birth defects or other reproductive harm. Some examples of these  
chemicals are:lead from lead-based paints, crystalline silica from bricks and cement  
or other masonry products, arsenic and chromium from chemically treated lumber.  
Your risk from these exposures varies, depending on how often you do this type of  
work. To reduce your exposure to these chemicals: work in a well ventilated area,  
and work with approved safety equipment, such as dust masks that are specially  
SKU 95848  
for technical questions, please call 1-800-444-3353.  
PAGE 5  
 
designed to filter out microscopic particles. (California Health & Safety Code §  
25249.5, et seq.)  
13.  
WARNING! People with pacemakers should consult their physician(s) before  
using this product. Operation of electrical equipment in close proximity to a heart  
pacemaker could cause interference or failure of the pacemaker.  
GROUNDING  
WARNING!  
Improperly connecting the grounding wire can result in the risk of electric shock.  
Check with a qualified electrician if you are in doubt as to whether the outlet is  
properly grounded. Do not modify the power cord plug provided with the tool.  
Never remove the grounding prong from the plug. Do not use the tool if the  
power cord or plug is damaged. If damaged, have it repaired by a service facil-  
ity before use. If the plug will not fit the outlet, have a proper outlet installed by  
a qualified electrician.  
GROUNDED TOOLS:TOOLS WITH THREE PRONG PLUGS  
1.  
Tools marked with “Grounding Required” have a three wire cord and three prong  
grounding plug. The plug must be connected to a properly grounded outlet. If  
the tool should electrically malfunction or break down, grounding provides a low  
resistance path to carry electricity away from the user, reducing the risk of electric  
shock. (See figure A.)  
2.  
3.  
The grounding prong in the plug is connected through the green wire inside the  
cord to the grounding system in the tool. The green wire in the cord must be the  
only wire connected to the tool’s grounding system and must never be attached to  
an electrically “live” terminal. (See figure A.)  
Your tool must be plugged into an appropriate outlet, properly installed and grounded  
in accordance with all codes and ordinances. The plug and outlet should look like  
those in the following illustration. (Se figure A.)  
fIGURE A  
fIGURE  
SKU 95848  
for technical questions, please call 1-800-444-3353.  
PAGE 6  
 
DOUbLE INSULATED TOOLS:TOOLS WITH TWO PRONG PLUGS  
1.  
2.  
Tools marked “Double Insulated” do not require grounding. They have a special  
double insulation system which satisfies OSHA requirements and complies with  
the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard  
Association, and the National Electrical Code. (See figure b.)  
Double insulated tools may be used in either of the 120 volt outlets shown in the  
preceding illustration. (See figure b.)  
ExTENSION CORDS  
1.  
2.  
Grounded tools require a three wire extension cord. Double Insulated tools can  
use either a two or three wire extension cord.  
As the distance from the supply outlet increases, you must use a heavier gauge  
extension cord. Using extension cords with inadequately sized wire causes a seri-  
ous drop in voltage, resulting in loss of power and possible tool damage.  
(See figure C, next page.)  
3.  
The smaller the gauge number of the wire, the greater the capacity of the cord. For  
example, a 14 gauge cord can carry a higher current than a 16 gauge cord.  
(See figure C.)  
4.  
5.  
When using more than one extension cord to make up the total length, make sure  
each cord contains at least the minimum wire size required. (See figure C.)  
If you are using one extension cord for more than one tool, add the nameplate am-  
peres and use the sum to determine the required minimum cord size.  
(See figure C.)  
6.  
7.  
If you are using an extension cord outdoors, make sure it is marked with the suffix  
“W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.  
Make sure your extension cord is properly wired and in good electrical condition.  
Always replace a damaged extension cord or have it repaired by a qualified electri-  
cian before using it.  
8.  
Protect your extension cords from sharp objects, excessive heat, and damp or wet  
areas.  
SKU 95848  
for technical questions, please call 1-800-444-3353.  
PAGE 7  
 
RECOMMENDED MINIMUM WIRE GAUGE fOR ExTENSION CORDS*  
(120 OR 240 VOLT)  
NAMEPLATE  
AMPERES  
(at full load)  
ExTENSION CORD LENGTH  
25 feet  
50 feet  
75 feet 100 feet 150 feet  
0 – 2.0  
2.1 – 3.4  
18  
18  
18  
18  
18  
14  
12  
18  
18  
18  
16  
14  
12  
10  
18  
18  
16  
14  
12  
10  
-
18  
16  
14  
12  
10  
-
16  
14  
12  
12  
-
3.5 – 5.0  
5.1 – 7.0  
7.1 – 12.0  
12.1 – 16.0  
16.1 – 20.0  
-
-
-
* based on limiting the line voltage drop to five volts at 150% of the rated amperes.  
fIGURE C  
SyMbOLOGy  
Double Insulated  
Canadian Standards Association  
Underwriters Laboratories, Inc.  
Volts Alternating Current  
V~  
A
Amperes  
No Load Revolutions per Minute (RPM)  
n xxxx/min.  
0
SKU 95848  
for technical questions, please call 1-800-444-3353.  
PAGE 8  
 
UNPACKING  
When unpacking, check to make sure that the product is complete and undamaged.  
If any parts are missing or broken, please call Harbor Freight Tools at the number shown  
on the cover of this manual as soon as possible.  
CHARGING  
1.  
2.  
NOTE: The Battery Pack (28) requires charging before first use. The first charge  
requires a one and a half hour charge prior to initial use of the Cordless Drill.  
Note: Always switch to a fresh battery when tool performance begins to diminish.  
Severe heat is most destructive to a battery; the more heat generated, the faster  
the battery loses power. A battery that gets too hot can be permanently damaged.  
Never over-discharge a battery by using the tool after itsperformance is decreasing.  
Never attempt to discharge a tool’s battery by continuing to pull the trigger. When  
tool performance begins to diminish, stop the tool, recharge the battery and use  
the fresh battery for optimal performance.  
3.  
When the Battery Pack requires recharging, a 1 hour charge allows the tool to  
operate at full power.  
4.  
5.  
Charging room temperature: 50° F. – 104° F.  
Depress both buttons at the rear of each side of the Battery Pack and slide unit back  
to detach from the Drill. Plug Battery Pack into Adapter (30) the same way it plugs  
into the Cordless Drill, then slide Adapter onto Charger (29), and plug the Charger  
into the nearest 120 volt, grounded, electrical outlet.  
6.  
7.  
While charging, the Battery Pack, Charger, and Adapter may become warm to the  
touch. This is normal, and does not indicate a problem.  
Once the Battery Pack is fully charged, disconnect the Charger from the electrical  
outlet. Disconnect the Adapter and the Battery Pack from the Charger.  
Battery  
Pack (28)  
Battery  
Pack (28)  
Adapter  
(30)  
Charger  
(29)  
Adapter  
(30)  
Charger  
(29)  
SKU 95848  
for technical questions, please call 1-800-444-3353.  
PAGE 9  
 
OPERATING INSTRUCTIONS  
NOTE: For additional information regarding the parts listed in the following pages, refer to  
the Assembly Diagram on page 13.  
WARNING! Remove the Battery (28) from the tool and set the Rotation Button  
(9) to its center, locked, position before making any adjustments, changing accessories,  
or storing the tool.  
Accessory Grip (14)  
Torque Indicator Arrow  
Chuck (16)  
Rotation Button (9)  
Torque Setting Ring  
(15)  
Trigger (10)  
2-Head Bit (3)  
Battery Pack (28)  
figure E.  
1.  
2.  
To install a drill/screwdriver bit: with the chuck pointing away from you, hold the  
Chuck Sleeve firmly in place and turn the Chuck (16) counterclockwise. Insert the  
shank of the bit all the way into the Chuck. While holding the Chuck Sleeve in place,  
turn the Chuck clockwise to lock the bit in place. The Chuck accepts up to 1/2”  
diameter bits. Insert the appropriate bit for your application and tighten the Chuck  
firmly. (See Figure E., above.)  
Secure the workpiece in place, using a vise or clamps (not included).  
Warning! Never change Torque Setting while drill is still rotating, as this can damage the  
drill.  
3.  
Decide on which setting to choose for application:  
Torque Settings (1-16):  
The different numbers on the Ring are an indication of how much torque the screw-  
driver will apply to the bit before the clutch slips, allowing the bit to stop and helping  
SKU 95848  
for technical questions, please call 1-800-444-3353.  
PAGE 10  
 
to prevent damage to the screw, bit, or workpiece. The higher the number, the more  
torque is applied before the clutch slips. Unless you are drilling, always start with a  
lower number to help prevent damage. This drill also has torque settings between  
the numbers to allow a greater range of control.  
Drill Setting (  
):  
This setting essentially prevents the clutch from slipping entirely. It is designed for  
drilling, but is not advised for using the screwdriver because it offers no protection  
against stripping the head or splitting the wood.  
4.  
5.  
6.  
7.  
Set the drilling torque by turning the Torque Setting Ring (15) to align the torque  
indicator arrow with the desired setting. (See Figure E., previous page.)  
When drilling in light gauge metal or wood, use a wooden block to back up the  
material to prevent damage to the workpiece.  
Mark the center of the hole to be drilled with a center punch (not included) to give  
a Drill Bit a start and to prevent it from “walking”.  
Lubricate the Drill Bit with cutting oil (not included) when drilling iron or steel. Use  
a coolant (not included) when drilling nonferrous metals such as copper, brass, or  
aluminum.  
8.  
Attach the Accessory Grip (14) to the drill by sliding the metal loop over the front  
of the drill and fastening it securely behind the Torque Setting. Turn the handle of  
Accessory Grip handle counterclockwise until it holds firmly. The Accessory Grip  
allows greater control over the Drill and makes it easier to resist being pulled out  
of alignment by torque.  
9.  
Insert the fully charged Battery Pack (28) into the Handle of the Cordless Drill.  
10.  
The Rotation Button (9) allows you to change the rotational direction of the Cordless  
Drill. For a clockwise rotation, move the Rotation Button to the right. For a counter-  
clockwise rotation, move the Rotation Button to the left. The center position locks  
the Trigger (10), helping to prevent the Drill from operating. The Forward/Reverse  
Indicator (21) lights up, when the Trigger is depressed, to show which direction the  
Drill is set.  
11.  
12.  
13.  
Make sure to hold the Cordless Drill firmly with both hands, as torque from the Mo-  
tor can cause the tool to twist.  
Operate the Drill, by squeezing the Trigger (10). The speed of the Drill can be con-  
trolled by varying the pressure on the Trigger.  
If Drilling:  
Use the Drill torque setting, as described above.  
SKU 95848  
for technical questions, please call 1-800-444-3353.  
PAGE 11  
 
Drill only as deep as necessary. Do not drill deeper than necessary into walls or other  
areas where you cannot identify any possible hazards behind the drilling surface.  
To reduce jamming as the Bit breaks through the workpiece, decrease the drilling  
pressure when the point of the Bit breaks through the workpiece.  
14.  
When you have drilled the hole, remove the Bit from the hole while the Cordless  
Drill is still running. This prevents the Bit from getting caught in the hole and caus-  
ing damage.  
15.  
16.  
When driving screws, start with a low torque setting.  
If the clutch starts slipping before the screw is in all the way, stop the drill, put the  
Rotation Button (9) in the center position and change the torque setting. Reset the  
rotation direction before continuing.  
17.  
Release the Trigger (10) to stop the Drill. Then, remove the Battery Pack, put the  
Rotation Button in the center position, and remove the bit from the Drill.  
INSPECTION, MAINTENANCE, AND CLEANING  
1.  
2.  
WARNING! Remove the battery Pack (28) from the tool and set the Rota-  
tion button (9) to its center, locked position before performing any inspection,  
maintenance, or cleaning.  
bEfORE EACH USE, inspect the general condition of the Cordless Drill. Check for  
misalignment or binding of moving parts, cracked or broken parts, leaking Battery  
Pack, damaged Charger wiring, chipped or broken Drill Bits, and any other condi-  
tion that may affect its safe operation. If abnormal noise or vibration occurs, have  
the problem corrected before further use.  
Do not use damaged equipment.  
3.  
4.  
DAILy: With a soft brush or cloth, remove all dirt and debris from the Cordless Drill.  
Do not immerse the Cordless Drill in any liquids.  
When the battery needs replacement keep in mind that the Nickel-Cadmium  
(Ni-Cd) battery in this tool must be recycled or disposed of properly.  
SKU 95848  
for technical questions, please call 1-800-444-3353.  
PAGE 12  
 
PARTS LIST  
Part  
Description  
QTy  
Part  
Description  
QTy  
1
Screw  
2
16  
Chuck (13mm)  
1
2
Sticker  
1
1
1
1
1
1
1
1
1
1
1
1
1
1
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
Screw  
1
1
1
1
1
1
1
1
1
8
1
1
1
1
3
2-Head Bit  
Gear Assembly Motor  
Right Shell  
4
Plate  
5
Battery Indicator Button  
Bit Clamp  
Cover  
6
Forward/Reverse Indicators  
Level Vial  
7
Battery Indicator PCB  
Left Shell  
8
Screw  
9
Rotation Button  
Trigger  
Insulated Pipe  
Battery Clamp Housing  
Wire  
10  
11  
12  
13  
14  
15  
R/R Indicator PCB  
Magnesium Shell  
Screw  
Battery Clamp  
Battery Pack  
Accessory Grip  
Torque Setting Ring  
Charger (not shown)  
Adapter (not shown)  
ASSEMbLy DIAGRAM  
SKU 95848  
for technical questions, please call 1-800-444-3353.  
PAGE 13  
 
PLEASE READ THE fOLLOWING CAREfULLy  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN  
THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR  
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE  
IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO  
REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR  
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN  
BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES  
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR  
REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACE-  
MENT PARTS THERETO.  
LIMITED 90 DAy WARRANTy  
Harbor Freight Tools Co. makes every effort to assure that its products meet high  
quality and durability standards, and warrants to the original purchaser that this product  
is free from defects in materials and workmanship for the period of 90 days from the date  
of purchase. This warranty does not apply to damage due directly or indirectly, to misuse,  
abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity,  
improper installation, normal wear and tear, or to lack of maintenance.We shall in no event  
be liable for death, injuries to persons or property, or for incidental, contingent, special  
or consequential damages arising from the use of our product. Some states do not allow  
the exclusion or limitation of incidental or consequential damages, so the above limitation  
of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL  
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF  
MERCHANTABILITY AND FITNESS.  
To take advantage of this warranty, the product or part must be returned to us with  
transportation charges prepaid. Proof of purchase date and an explanation of the com-  
plaint must accompany the merchandise. If our inspection verifies the defect, we will either  
repair or replace the product at our election or we may elect to refund the purchase price  
if we cannot readily and quickly provide you with a replacement. We will return repaired  
products at our expense, but if we determine there is no defect, or that the defect resulted  
from causes not within the scope of our warranty, then you must bear the cost of returning  
the product.  
This warranty gives you specific legal rights and you may also have other rights  
which vary from state to state.  
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353  
Record Product’s Serial Number Here:  
Note: If product has no serial number, record month and year of purchase instead.  
Note: Some parts are listed and shown for illustration purposes only, and are not available  
individually as replacement parts.  
SKU 95848  
for technical questions, please call 1-800-444-3353.  
PAGE 14  
 

Belkin Network Card N150 User Manual
Black Decker Blender FR220 User Manual
Bowers Wilkins Speaker 800 User Manual
Brocade Communications Systems Switch VA 40FC User Manual
Brother All in One Printer MFC L8600CDW User Manual
Brother Label Maker PT 300 User Manual
Campbell Hausfeld Network Card SDM CVO4 User Manual
Casio Clock Radio MA0906 EA User Manual
Celestron Telescope NexStar HC User Manual
ChefScape Blender SE650 User Manual