E4le40ctlbr.i/c88H0olbis. t
44006
SET UP AND OPERATING INSTRUCTIONS
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright© 2000 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Cover Revised 09c
be caught in moving parts. Nonskid
footwear is recommended. Wear re-
strictive hair covering to contain long
hair. Wear appropriate work clothing.
13. AVOID UNINTENTIONAL START-
ING. Be sure that you are prepared
to begin work before turning the start
switch on.
8. USE EYE, EAR AND BREATHING
PROTECTION. Wear ANSI-ap-
proved impact safety goggles if you
are producing metal filings or wood
chips. Wear a NIOSH-approved dust
mask or respirator when working
around metal, wood, and chemical
dusts and mists. Use hearing protec-
tion when working in a loud or noisy
environment.
14. STAY ALERT. Watch what you are
doing. Do not operate this machine
when you are tired.
15. DO NOT OPERATE THIS MACHINE
WHILE UNDER THE INFLUENCE
OF ALCOHOL, DRUGS, OR PRE-
SCRIPTION MEDICINES.
16. CHECK FOR DAMAGED PARTS.
Before using any tool, any part that
appears damaged should be carefully
checked to determine that it will oper-
ate properly and perform its intended
function. Check for alignment and
binding of moving parts, any broken
parts or mounting fixtures, and any
other condition that may affect proper
operation. Any part that is damaged
should be properly repaired or re-
placed by a qualified technician.
9. DO NOT ABUSE THE POWER
CORD. Protect the power cord from
damage, either from impacts, pulling
or corrosive materials. Do not yank
machine’s cord to disconnect it from
the receptacle.
10. DO NOT OVERREACH. Keep proper
footing and balance at all times. Do
not reach over or across running
machines.
17. REPLACEMENT PARTS AND AC-
CESSORIES. When servicing, use
only identical replacement parts,
which are available from Harbor
Freight Tools.
11. MAINTAIN TOOLS WITH CARE.
Keep tools sharp and clean for bet-
ter and safer performance. Follow
instructions for lubricating and chang-
ing accessories. Inspect power cord
periodically and, if damaged, have it
repaired by an authorized technician.
Inspect all moving parts and mount-
ing bolts prior to use. Control handle
and power switch must be kept clean,
dry, and free from oil and grease at
all times.
18. NOT TO BE USED FOR AIRCRAFT
PURPOSES.
19. NEVER LIFT PEOPLE AND ANI-
MALS OR HOIST LOADS OVER
PEOPLE.
Special Warnings when using this
Electric Hoist
12. REMOVE ADJUSTING KEYS AND
WRENCHES. Be sure that keys and
adjusting wrenches are removed from
the tool or machine work surface be-
fore operation.
1. Using this powerful tool may cre-
ate special hazards. Take particular
care to safeguard yourself and those
around you.
SKU 44006
For technical questions, please call 1-800-444-3353.
Page 3
2. The Cable.
Be sure the cable is in good condi-
6. WARNING: Handling the cord on
this product will expose you to lead,
a chemical known to the State of
California to cause cancer, and birth
defects or other reproductive harm.
Wash hands after handling.
tion, and is attached properly.
Do not use the Hoist if the cable is
frayed, kinked, or wrapped improperly
on the reel.
Do not replace the cable with a cable
of lesser strength.
(California Health & Safety Code §
25249.5, et seq.)
3. Power Supply.
7. People with pacemakers should
consult their physician(s) before use.
Electromagnetic fields in close prox-
imity to heart pacemaker could cause
pacemaker interference or pacemak-
er failure.
Be sure the power cord and control
handle are in good condition. Avoid
use in wet conditions, or exposing the
electrical components of this hoist to
moisture.
Route the power cord so that it is out
of the way of other tools and equip-
ment. Take care to prevent damage
to the power cord, or control handle
cord. If the cord becomes damaged,
repair or replace it before using the
hoist.
8. The Warnings, Cautions, and Instruc-
tions discussed in this instruction
manual cannot cover all possible con-
ditions and situations that may occur.
It must be understood by the operator
that common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
4. Stand Back.
Stay out of the direct line that the
cable is pulling. If it slips or breaks, it
will “whiplash” along this line.
Never stand underneath a weight be-
ing lifted.
Always wear ANSI approved eye
protection when working around tools
and equipment.
Do not hold the cable while using
the hoist, as your hand can become
caught.
Keep hands, clothing, hair and jew-
elry clear of the hoist while in use.
Use a spotter to assist you in assur-
ing that it is safe to operate the hoist.
5. Power Limits.
Do not attempt to exceed the pulling
limits of this hoist.
Assure that the mount to which the
hoist is attached will hold the weight
you will apply using this hoist.
REV 04d; 06k; 09c
SKU 44006
For technical questions, please call 1-800-444-3353.
Page 4
MOUNTING
Note: Before use, attach your hoist to
an overhead pipe using the included
brackets as follows:
1. Find the 2 Fixing Rings (#3) and the
Hex Head Bolts (#4).
Figure 2. Optional Pole Mount.
Note: Your hoist may be mounted on a
fixed overhead pipe, or attached to a
pole on a rotating pillar.
Figure 1. Mounting the Hoist.
OPERATION
2. Place the Fixing Rings over a suitable
pipe, in the position you wish to
mount the hoist.
1. The cable spool will not turn freely.
To pull out or wind up cable, you must
operate the power switch.
3. Have an assistant hold the hoist
in place while you install the Bolts
through the Fixing Rings into the
threaded holes in the Fixing Rack (#1)
of the hoist.
2. To operate the power switch, take the
Handle Base in your hand. Press the
upper part of the rocker Switch to reel
in the cable. Press the lower part of
the rocker cable to reel out cable.
4. With the hoist in the correct position,
3. Check to be sure it is safe to lift or
pull the item.
firmly tighten the bolts.
4. To pull out the cable, grasp the lift
hook, and pull it away from the hoist
while pressing the lower part of the
power Switch . Always leave at least
three turns of cable on the spool to
prevent pulling the cable out of the
Hoist.
5. Attach the cable firmly to the item
using the lift hook or pulley lift hook.
Never wrap the cable around the
object and hook onto the cable itself.
This can cause damage to the ob-
REV 02a
SKU 44006
For technical questions, please call 1-800-444-3353.
Page 5
440 lb.
880 lb.
Single Line
Double Line
Configuration
Configuration
ject being pulled, and kink or fray the
cable.
MAINTENANCE
1. Lubricate the cable occasionally with
a light oil. Check that it is in good
condition.
6. Stand clear, and when it is safe to
do so, use the power Switch in the
Handle Base to retract the cable, and
hoist the item as desired.
2. Check to be sure the hoist is properly
attached to its mounting pole. Make
sure the bolts are tight.
3. Periodically check the condition of the
electrical cords, plugs and controls.
PLEASE READ THE FOLLOWING
CAREFULLY
Figure 6
7. Wind the cable properly around the
spool.
THE MANUFACTURER AND/OR DISTRIBUTOR HAS
PROVIDED THE PARTS DIAGRAM IN THIS MANUAL
AS A REFERENCE TOOL ONLY: NETHER THE
MANUFACTURER NOR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND
TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REPAIRS TO THE PRODUCT OR THAT
HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS
OF THE PRODUCT: IN FACT THE MANUFACTURER
A ND/OR DISTRIBUTOR EXPRESSLY STATES THAT
ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF
HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT
OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACE-
MENT PARTS THERETO.
8. Leave at least 3 turns of the cable
around the reel, to prevent the cable
from coming unattached to the reel.
9. If you are unable to lift a load, do not
continue to operate the power switch.
This can result in damage to the mo-
tor.
SKU 44006
For technical questions, please call 1-800-444-3353.
Page 6
PARTS LIST
RACK
Rev 00k; 05g
SKU 44006
For technical questions, please call 1-800-444-3353.
Page 7
ASSEMBLY DIAGRAM
Rev 00k; 05g
SKU 44006
For technical questions, please call 1-800-444-3353.
Page 8
WIRING DIAGRAM
S1
S3
C
Pendant Switch
Micro Switch
Capacitor
Sth Overheat Protector
Rev 02h, 08d
SKU 44006
For technical questions, please call 1-800-444-3353.
Page 9
90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free
from defects in materials and workmanship for the period of 90 days from the date of
purchase. This warranty does not apply to damage due directly or indirectly, to misuse,
abuse, negligence or accidents, repairs or alterations outside our facilities, criminal
activity, improper installation, normal wear and tear, or to lack of maintenance. We
shall in no event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our product.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY
IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the
complaint must accompany the merchandise. If our inspection verifies the defect, we
will either repair or replace the product at our election or we may elect to refund the
purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that
the defect resulted from causes not within the scope of our warranty, then you must
bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which
vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Rev 08d
SKU 44006
For technical questions, please call 1-800-444-3353.
Page 10
|