ROTARY TOOL KIT
WITH 60 ACCESSORIES
Model 41695
ASSEMBLY AND OPERATING
INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
©
®
Copyright 2002 by Harbor FreightTools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or
form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
REV 05/05
10. Disconnect power. Unplug adapter when not in use.
11. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches are
removed from the tool or machine work surface before plugging it in.
12. Avoid unintentional starting. Be sure the switch is in the Off position when not in use
and before plugging in. Do not carry any tool with your finger on the switch, whether it is
plugged in or not.
13. Stay alert. Watch what you are doing, use common sense. Do not operate any tool when
you are tired.
14. Take caution as some woods contain preservatives such as copper chromium ar-
senate (CCA) which can be toxic. When cutting these materials extra care should be
taken to avoid inhalation and minimize skin contact.
15. Check for damaged parts. Before using any tool, any part that appears damaged should
be carefully checked to determine that it will operate properly and perform its intended
function. Check for alignment and binding of moving parts; any broken parts or mounting
fixtures; and any other condition that may affect proper operation. Any part that is dam-
aged should be properly repaired or replaced by a qualified technician.Do not use the tool
if any switch does not turn On and Off properly.
16. Guard against electric shock. Prevent body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerator enclosures.
17. Replacement parts and accessories. When servicing, use only identical replacement
parts. Use of any other parts will void the warranty. Only use accessories intended for use
with this tool. Approved accessories are available from Harbor Freight Tools.
18. Do not operate tool if under the influence of alcohol or drugs. Read warning labels
on prescriptions to determine if your judgment or reflexes are impaired while taking drugs.
If there is any doubt, do not operate the tool.
19. Use proper size and type extension cord. If an extension cord is required, it must be of
the proper size and type to supply the correct current to the tool without heating up.
Otherwise, the extension cord could melt and catch fire, or cause electrical damage to the
tool.This tool requires use of an extension cord of 0 to 10 amps capability (up to 50 feet),
with wire size rated at 18 AWG. Longer extension cords require larger size wire. If you are
using the tool outdoors, use an extension cord rated for outdoor use (signified by “WA” on
the jacket).
20. Maintenance. For your safety, maintenance should be performed regularly by a qualified
technician.
Note: Performance of this tool (if powered by line voltage) may vary depending on varia-
tions in local line voltage. Extension cord usage may also affect tool performance.
Warning:The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be under-
stood by the operator that common sense and caution are factors which cannot be
built into this product, but must be supplied by the operator.
For technical questions, please call 1-800-444-3353.
SKU 41695
Page 3
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities, contain chemicals known [to the State of California] to cause
cancer, birth defects or other reproductive harm. Some examples of these chemicals
are:
-
-
Lead from lead-based paints
Crystalline silica from bricks and cement or other masonry
products
-
Arsenic and chromium from chemically treated lumber
(California Health & Safety Code 25249.5, et seq. )
Warning: The brass components of this product contain lead, a chemical known to the State
of California to cause birth defects (or other reproductive harm).
(California Health & Safety Code § 25249.5, et seq.)
Warning: Exposure to aluminum oxide (a dust generated from material removing processes)
can result in eye, skin and breathing irritation. Always use a NIOSH (National Institute for
Occupational Safety and Health) approved respirator and safety goggles. Avoid skin expo-
sure. Proper ventilation in the work area is required.
Additional RotaryTool Safety Warnings.
1. Make sure accessories are rated for the speed recommended for this tool.
2. Securely clamp workpiece as the Rotary Tool spins at very high RPM rates. Never hold a
workpiece in your hands.
3. Always disconnect the DC power source before changing accessories.
4. Do not grind or sand near flammable materials.
5. After use, do not touch the bit or collet until the tool has had enough time to cool off.
6. If the bit or accessory bogs down or becomes jammed, make sure to turn off the switch
and unplug from the power source before clearing the bit or accessory.
7. Always feed the accessory or bit in the proper direction. Feed in the direction that the
cutting edge is exiting the workpiece (that is the same direction chips are thrown).
8. Always bring the tool up to speed before contacting the material.
9. Make sure there are no foreign objects, such as nails, in your workpiece.
10. Don’t use dull or damaged bits. Dull or damaged bits may break off and cause serious
injury. Replacement accessories are available at Harbor Freight Tools.
11. After changing bits or accessories, make sure the collet is securely fastened.
Unpacking
When unpacking, check to make sure the parts listed on page 6 are included. If any parts
are missing or broken, please call Harbor Freight Tools at the number on the cover of this
manual as soon as possible
For technical questions, please call 1-800-444-3353.
SKU 41695
Page 4
Operation
Note: Always disconnect the tool from the power adapter while loading, unloading, or adjust-
ing accessories.
1. Choose the appropriate Collet (3) for the shank of the accessory you are using.
2. Just above the collet shaft on the end of the tool, there is a shaft lock button. Depress that
button to lock the shaft so that you can open the Collet (3).
3. Remove the Collet Nut (13) on the tip of the tool and add the appropriate Collet (3). Put
the bit or accessory you want in the Collet (3). Continue to depress the shaft lock button
while tightening the Collet Nut (13).
4. Make certain that the power switch is in the off (O) position. Plug the Adapter (2) into a
properly grounded, 120 VAC outlet. Connect the plug from the Rotary Tool (1) to the
connector on the end of the adapter’s cord.
5. Hold the tool firmly in one hand. Turn the toggle switch on ( I ) and wait until the tool
reaches full speed before contacting the workpiece.
6. When finished, turn off (O) the toggle switch and unplug the unit.
OperationalTips.
1. When you turn on the tool, hold it a safe distance in a direction away from your face.
2. Practice on scrap material while getting use to the feel of the tool.
3. Never lean on the tool. Allow the speed of the tool to do the work for you. Lightly contact
the material. It is better to make several passes on a workpiece than to try to remove a lot
of material in one pass. A gentle touch works best. If you feel the job is not getting done,
change to a more powerful cutter.
4. Plastics and similar materials will melt when contacted with high speed accessories. Start
very slowly and monitor the material carefully.
Accessory Tips. (Some of the many uses.)
1. Mandrels are the shanks with a threaded or screw head. They are required when you
use the cutoff wheels, polishing wheels, and sanding discs. The mandrel without the nut
on the end is for the felt polishing wheels. For cutoff wheels and sanding discs, remove
the nut on the end of the mandrel, add the wheel or disc, and replace the nut.
2. Cutters are used for cutting, carving and slotting materials.
3. Grinding Stones are used for sharpening cutting tools, screwdrivers etc. They can also
be used to deburr any metal after the cutting process. Also, they can be used to remove
excess glaze on ceramics.
4. Cutting Wheels are used for slicing or cutting off bolt heads, nuts, etc.
5. Wire Brushes clean silverware, jewelry, and antiques.
6. Sanding accessories can be used on a variety of workpieces, ranging from models to fine
furniture.
7. Polishing accessories bring metal surfaces to a smooth finish.
REV 02/05
For technical questions, please call 1-800-444-3353.
SKU 41695
Page 5
Parts List
Part
1
Description
Pieces
Qty.
1
Rotary Tool
2
Power Pack Adapter
1
3
Brass Collet Set
4
20
10
8
1
1
4
Diamond Burr Set ( / ” Shank)
1
8
3
5
Mounted Stone Set ( / ” Shank)
1
32
1
6
Sanding Drum Set ( / ” Shank)
1
8
1
7
Cut Off Wheel Set ( / ” Shank)
6
1
8
1
8
Buffing Wheel Set ( / ” Shank)
5
1
8
3
1
9
Wire Wheel Set ( / ” & / ” Shanks)
3
1
32
8
10
11
12
13
14
Grinding Stone
1
1
Drill Bit Set (1, 2.25, & 3 mm; / " dia.)
4
1
8
3
Carbide Burr ( / ” Shank)
1
32
Collet Nut
Case
1
1
Maintenance
Note: Always disconnect the power adapter from the electrical outlet before attempting any
maintenance.
1. While wearing safety goggles and a full face shield, use compressed air to clean out the
tool’s vents.
2. Clean the collet shaft of any dirt or debris.
3. Wipe the tool down with a soft cloth. Do not use any solvents to clean the tool as they will
permanently damage the tool.
4. If the Rotary Tool begins to work less efficiently, or slow down, have the internal brushes
replaced by an qualified technician.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS MANUAL
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS
OFTHE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATESTHAT
ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING
OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO,
OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
NOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
REV 02/05
For technical questions, please call 1-800-444-3353.
SKU 41695
Page 6
Assembly Drawing
NOTE: Case (14) - not shown.
Note: To use the cutoff wheels and polishing wheels, see Accessory Tips on page 5.
REV 02/05
For technical questions, please call 1-800-444-3353.
SKU 41695
Page 7
|